Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner "burned out" so we replaced the one and replaced the other that seemed to be cooling down.
13 of 23 peoplefound this instruction helpful.
Cheryl from Sequim, WA
A Bit Difficult
30 - 60 mins
Nutdriver, Pliers, Screw drivers
Basically removed the screws holding the op on and removed the vent from back. Just "figured it out" and now it works. Wish I could be more helpful. Recommend moderate experience and confidence.
Turned off power to cooktop. Disconnected power wires and removed cooktop from counter. Removed screws holding on the cooktop surface. Separated cooktop surface from cooktop. Removed 4 screws holding control panel, then removed 2 screws holding selector switch. Removed 2 wires plugged into selector switch. Installed new selector swi
... Read moretch and reassembled cooktop.
Read less
Was this helpful?
Thank you for voting!
Outer ring of burner did not work
5 of 5 peoplefound this instruction helpful.
Barry from Bradenton, FL
Really Easy
Less than 15 mins
Pliers, Screw drivers, Socket set
1- opened oven door 2- unscrewed 2 screws underneath top with a socket wrench 3- unscrewed clips that held burner 4-used needle nose pliers to pull off wire clips off old burner 5- placed wires onto new burner 6- opened clips to make it easier to reinsert burner 7-reattached burner 8-Replaced top
... Read morer />The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws
Read less
Was this helpful?
Thank you for voting!
The small burner inside the double burner shortd out.
5 of 5 peoplefound this instruction helpful.
david from PORT ORANGE, FL
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
The first thing was to watch U-Tube . The replacement burner was being replaced in a GE glass top range. Exter tools were required than depicted in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years
Was this helpful?
Thank you for voting!
Large burner would not heat
5 of 6 peoplefound this instruction helpful.
Charles from Carthage, NY
Really Easy
Less than 15 mins
Nutdriver
I ordered the wrong part to start with. (READ CAREFULLY!) I reordered the correct part and it was simple. I unpluged the old element, plugged in the new one replaced the drip pan and trim ring and we were back cooking. Service was fast, lady I spoke with on the phone to exchange parts was knowegable and nice. Great people to deal wi
... Read moreth.
Read less
Was this helpful?
Thank you for voting!
outside element burned out
4 of 4 peoplefound this instruction helpful.
peter from westfield, MA
Really Easy
Less than 15 mins
Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs. plugged in the new element and screwed it in place
Was this helpful?
Thank you for voting!
Burner element was burnt
4 of 5 peoplefound this instruction helpful.
Chandra from Naugaeuck, CT
Really Easy
Less than 15 mins
Screw drivers, Socket set
It was very easy. First turn off the power. Remove two screws to pick up the hood then remove two screws holding the element. Tag the wires with number. Unplug the old burner attach the wires to new burner. Attach two screws with spring to hold the burner, put the hood down and put the screws holding the top hood.
Was this helpful?
Thank you for voting!
The front right outer element was defective.
4 of 5 peoplefound this instruction helpful.
Peter from Abbeville, LA
Really Easy
15 - 30 mins
Pliers, Screw drivers
My cooktop is a stand alone unit mounted in a counter top not associated with an oven. -Removed power to the cook top. Breaker off. -Lifted the cook top straight up from the counter top and placed two 24 inch board strips to support it above the counter top. This was very easy by pushing up from the bottom of the cook top. T
... Read morehis is a two person job preferably. -Removed the six phillip screws below the glass surface edge. 3 in the front, three in the back. -Remove knobs and remove the glass top by lifting straight up. -Record the wire positions on the element on paper and remove the connections. -The element is mounted on two spring loaded studs that have spring clips as a retainer. Remove the two clips by pulling straight up with a plier or needlenose. -The replacement element did not come equipped with the two mounting ears that the original had. I removed the two ears from the defective element and installed them on the new element. Very easy. Two phillips screws. The elements have perferations in the correct areas to accommodate this. -Placed the new element in position and reinstalled the spring clips. -Install the wiring terminals in the correct positions. -Reinstalled the glass surface and the six phillips screws. Reinstall the knobs. -Lower the cook top back into its counter top position. -Return power to the cook top. -Installation complete. Very simple!
Read less
Was this helpful?
Thank you for voting!
The dual burnner had somthing drop on it and it went out
3 of 3 peoplefound this instruction helpful.
Thad from Layton, UT
A Bit Difficult
15 - 30 mins
Screw drivers
I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the
... Read more burner, then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.
Read less
Was this helpful?
Thank you for voting!
Inside burner would no longer heat
3 of 3 peoplefound this instruction helpful.
John from CHARLESTOWN, NH
Easy
15 - 30 mins
Screw drivers, Socket set
I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to
... Read more lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck
Read less
Was this helpful?
Thank you for voting!
Small front burner on our glass top stove died.
3 of 3 peoplefound this instruction helpful.
Robert from FLEMING ISLE, FL
Really Easy
15 - 30 mins
Screw drivers
Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.
Was this helpful?
Thank you for voting!
Control awitch was bad
3 of 3 peoplefound this instruction helpful.
Gary from CLEARWATER, FL
Easy
Less than 15 mins
Nutdriver, Pliers, Screw drivers
Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.
Was this helpful?
Thank you for voting!
Previous home owners replaced 3 drip bowls with wrong style
3 of 4 peoplefound this instruction helpful.
Diane from Corpus Christi, TX
Really Easy
Less than 15 mins
I removed the heating elements and the drip bowls (wrong style). I then positioned the correct drip bowls on the stove and reinserted the heating elements. I snapped the heating coils into the small slots on the far side of the bowls to make sure that the heating elements would lay flat. The whole process took less than 2 minutes.
Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. C
... Read moreonnected the wires and resecured top to base. Turned on the current and it worked beautifully.
Read less
Was this helpful?
Thank you for voting!
switch shorted out large selective burner quit
3 of 5 peoplefound this instruction helpful.
dennis from buckley, WA
Easy
15 - 30 mins
Screw drivers
turn off breaker, two screws hold down cooktop, 8 screws take top off cooktop. unplug switch, install new switch. repair loose connections. put back together. pretty simple
My Orders
