911404 - Instructions

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put ... Read more the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!

Used nut driver, removed 2 screws and removed old element. Reversed procedure for installion of new part. Can't believe ordered part one day & recieved it next day. Fantastic service. Will definitely call company again.

Installation was really easy. Remove the old bake element, plug the new one in, took at most 10 minutes.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in ... Read more the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

Turned off power to oven. Lifted off the oven door. Removed four 1/4 " bolts from outside of fan housing. Removed two 1/4" bolts holding element. Removed element from three clips holding it to upper oven surface. Unplugged two element wires. Reassembly was the reverse. I am an auto mechanic by trade and this was a fairly simple process.

Remove control panel: Made a layout of the wire colors and IDs. The new panel was sighly different. Had additional conponent which I ignored because it did not match the wires or IDs I had recorded. The only wire that I did not connect was the ground (Green wire) The place for it on the new board was crossed out. After I placed the wires ... Read more where it should go on the new board and turned back on the power. I tested all the functions and they all worked the firsy time. I was very happy with the results. What I think they should provide with the new panel was a conponet layout of the new board.

First of all, go to circuit breaker box and switch off the power to the oven.

Return to oven and verify the power is definitely off.

Open oven door to 'vent' position and remove door. Return hinges to closed position. Remove all racks.

Using nut driver (1/4-inch) remove the two screws just above the elem ... Read more ent.

Gently rock the element back and forth while pulling gently toward yourself. You should see two wires emerging from the layer of insulation in back of oven. When you have enough wire exposed, use long-nose pliers to gently rock the 'Faston' connectors and pull them off the element's male connectors.

Insert new element and re-install the connectors, being certain they are fully engaged.

Fasten the new element to the back wall of the oven using nut driver. Be careful to not cross-thread - gentle is the word!

Turn the circuit breaker on and very briefly turn the oven to Bake and verify the element is heating. It likely will smoke a bit.

Re-install the racks and the door. Reset the clock.

You should be done and your oven should run for many years..

removed oven --removed back panel to disconnect sensor splice- installed new one. removed oven door --took it all apart--removed old gasket and installed new one.

DISCONNECTED THE CIRCUIT BREAKERS.Removed 2 long screws from the inside upper frame accessable after the door is opened. Loosened 4 screws which held the unit in place.Copied the location and color of all the wires attached for future reference. With needlenose pliers pulled each wire at the base. Removed the old unit and replaced with ... Read more new unit. Re-mounted the wires. Secured the unit with 4 original screws and then fastened the unit with the two long screws back to the door frame.(this was second unit delivered. The first replacement had the same error )Turned on power and all is well.