911401 - Instructions

First I turned the power off at the breaker box. Then I removed the two screws at the rear of the oven and un-secured the three clips(top of stove) that all hold the element in place. Carefully I pulled the element out of the back of the stove to expose and pull out the electrical wires and their connectors. At this point I used the multi ... Read more meter to CONFIRM no power. With no power present I un-clipped the electrical connections and then did all the above steps in reverse. 15 - 20 minutes total repair time.

[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.

[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back ... Read more into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've wit ... Read more hstood the modification.

Removed burned out element and discovered replacement element had a different back plate and different hole pattern. Also, the electical connecttion from power wires to ends of element were a TOTALLY different size, both in hole size and size of material that hole was placed. This tood a lot of slow increasing the size of the hole time. ... Read more Also, the backplate was a different size with a two hole pattern at the top of the plate, as oppossed to the original plate with holes centered at the sides of the plate. Had to drill holes in back oven wall higher than I wanted, as the oven wall had a depression in the back wall and I could not drill at that point. By drilling holes that were higher than previous holes, there was now a 1/2" opening at the bottom of this plate. Used a hack saw and cut off a piece of the old plate to slip underneath, then screwed in the new plate, thus filling the remaining opening, and securing the additional hand made additional plate. This was a lot more than I had bargain for, and when I turned on the oven, it did not work! I re-checked the connection of the power wires to the grid element and found one of the connections to be disconnected. Reconnected this wire and everything is just ducky now.

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping

Removed mounting screws and element only pulled out about 2 inches. Disconnected wires and had to drill slightly bigger hole in element ends to reattach wires. Element mounting bracket was different than old element. Had to use one existing screw hole in oven back and drill a new one.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Ordered new part on-line for less than 1/2 of local price...including shipping. Local shop would have taken 10 days for part at twice the price. Mine arrived in 72 hours...and Sunday dinner was sav ... Read more ed!

Truned off the power took out the two screws holding the old element disconnect the power leads and put in the new element. Was great to recieve the new element in one day, the day before Xmas.

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip discon ... Read more nected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

The repair was remarkably simple. Had i a nut driver, it would have been simpler still. Nonetheless, I managed to remove the nuts affixing the element to the back of the oven with a wrench, pulled out the old element, reattached the wires (they slipped in with ease), replaced the element, tightened the nuts and, presto, I was done. I s ... Read more uspect I saved over $100, though would rather my wife not know for fear it will be spent elsewhere;-)

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the o ... Read more fficial Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

Removed screws holding old element; removed back panel. Attached new element with old screws and replaced panel.

The entire element was replaced. Since the oven is proably older than me (about 30 years) the holes did not light up exactly so 2 new holes had to be drilled. It is working great now and I'm happy to find a part that works.

1. Turn breaker off at breaker box. 2.Disconnect old broil element. Pull electric wires out 3-4 inches from BACK of oven. Clamp wires or tie off so they do not retreat behind back oven wall. INSTALL wires to new element and secure back plate. Install NEW clamps to new element. Switch on breaker and check operation.