911366 Kenmore Range - Instructions

Followed the video step by step, made the job simple and easy. Did not know there were springs attached to the lower part of hinge till watching video. Parts were genuine GE manufacturer parts which fit perfectly. Very helpful staff and great customer service. My model number did not match perfectly with others listed but the hinge pa ... Read more rt is identical.

Pull the door off the hinges. pull drawer out of range.Take sping off both frame and hinge arm. Unscrew three screws holing hinge in palce. pull old hinge out , put new hinge in . reinstall screws, spring, drawer , and door. Get the wife to make cookies.

Well after fighting with the door for a month, i went on this site and using their information, i found the model number (in the process i found the receipt for the oven and found out it was 20 years old still looks and works like new. Pulled the door up and off the hinges, removed the drawer, saw the spring was in the middle hole, remov ... Read more ed three screws pulled out old hinge. Installed new hinge, 3 screws and the spring. put the door back on and wow it worked! Thanks!

Used Phillips screw driver, installed guide, applied lubricant.

Just watched the video.

I unscrewed the broken hinge, removed the tension spring and replaced the old hinge with the new one. total time 5 mins works great.

Watched the video and did exactly as it instructed. Very easy to do, took 10 minutes in all.

I could not get a lens cover due to the fact ge does not make any more since the appliance is an older model. Thanks to part select they had the part which I badly needed. It was easy to installed. Thanks again part select.

I utilized the you tube video installation for instruction. The video was clear and easy to follow along. I was able to pull off the door and replace the the right and left hinges within 10 minutes. The videos made it very simple! Thank you

replaced both hinges in no time flat and it was easy to find the part and instructions on parts select. Thank you

Very,very easy. Just like the video described. Removed three screws. Released the spring and removed the old hinge from the slot. Slipped the new hinge in the slot,replaced the screws and reattached the spring. Job done! Great service!

Followed YouTube video from PartsSelect. It was real easy to do and that video was helpful. Took off door by sliding it up off hinges, disconnected springs, unscrewed hinges & slid them out - reversed to install. Worked perfect, parts were exactly right and parts came within 2 days.

There were 3 ? Types of black burner dishes and 3 types of burner caps. The information I collected did not hint about the different sizes. We sent back 2 caps for the proper ones. Meantime 3 of the dishes were on backorder. I installed the one dish I had. Later the 3 backorder dishes arrived. I began to install them when I discov ... Read more ered I needeed more than one size. I am a retired aerospace engineer. I had to use my file and hammer to fit experiences to make up for my parts ordering deficiency. The new dishes, mounting holes, were different than the one I had previously installed . So in order not to return them and wait an additional few weeks , I filed the mounting holes sufficient to be able to mount them. Then I put the next part on and discovered that it did not fit the new location of the igniter . I filed the approx 1/2" dia hole from round to a "d"configuration on 3 parts , that allowed the igniter to function in two of the new locations . The fourth and smallest burner required an additional 1/4" spacer to move the gas supply riser closer tothe igniter. The burners are all working as new. No fire hazards. My wife does not know the goofs I made. I had to use some inventive methods and I'm still her hero. I would caution all di it yourself people to become very familiar with the parts they need. They may all look the same to the novice but there are slight differences that should require replacement and could take away your hero status.

just look at the door where the screws were. remove them and the rest was obvious. done! whalla ;) I was glad to have found partsellect.com

Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor ... Read more wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.