911366 Kenmore Range - Instructions

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cav ... Read more ity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.

Getting the original screws out was a pain, but once I got them out I disconnected to old wires and attache the new wires. Installing the new igniter was VERY easy compared to removing th original one!

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part onl ... Read more y coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

I have a GE Profile Gas Range that was installed by the builder in 1997. The porcelain bowl under the grate had chipped on all the elements. I replaced them easily..quickly...and was very cost effective...thanks for the great service...great site to order from. AC

Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.

I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!

Took top off, removed wires from old spark module and put them on new one. Very easy and quick, works very well now.

Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the ... Read more plug, reinstall the two screws and you are done!

Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!

Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.

Open and slide door upward off of hinges. Removed bottom drawer to access hinge spring. Detached spring, noting proper hole in hinge for reinstallation. Removed three screws holding hinge and removed hinge. Compared new part to old...exact match. Inserted hinge, and reinstalled the three screws. Reattached spring in hinge hole. Sli ... Read more d door back down onto hinges. Done in four minutes flat!

Removed old hinges and installed new hinges.
Hardest part was determining that worn hinges were the cause of problem, then ordering replacements. GE website hinge on exploded view did not look like hinges I removed.Thanks to Google I got on to PartSelect.com website where excellent pictures of hinges and one-inch grid confirmed they ... Read more sold exactly what I wanted for my 13-year old range, the model number of which was not even on the GE website.

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip discon ... Read more nected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.