9113658813 Kenmore Range - Instructions

removed the gas burner which allowed easy access to undo the old igniter.
opened the wire hatch in the back of the oven cavity, and also took off the cover (two screws) on the back panel to allow access to the igniter connector.
I cut the wires to the old igniter, leaving lots of wire, stripped the wire, and then hooked up the n ... Read more ew igniter using the supplied ceramic / hi-temp twist on connectors.
then just closed up everything in reverse.
helps to take off oven door, and you need access to the back side of the oven.

Followed previous posts, just took out the metal pan (2) 1/4" head screws. Removed the ignitor bracket (2) 1/4" head screws. Disconnected the existing ceramic wirenuts. Removed the ignitor from the bracket......this was the hardest part as the self threading screw stripped out in the sheet metal. Took some time to remove that screw an ... Read more d re-tap the hole to #10-32. Once that was done used a #10-32 x 1/2" machine screw with lock washer. All went back together fine from there.

I put the grates in backwards and the wife had to turn them around after teasing me about it......maybe I should do more baking.......

Before removing screws, I reached in and felt for where the upper end of the spring attached to the hinge. There are three holes in the end of the hinge arm, so I wanted to be sure of which hole to use. (The holes are very close together, so if the spring falls out before you determine which hole it was in, it probably won't matter so l ... Read more ong as you are sure to use the same hole on both new hinges.) I then removed three Phillips screws per hinge. Once the hinge was loose, I could wiggle it around and release enough of the spring tension to slip the top end of the spring out of the hole on the hinge arm. Then I pulled out the old hinge and inserted the new one and replaced the three screws. Without the tension, the lower end of the spring fell out of the little hole in the oven bottom where it normally attaches. Our gas oven has a broiler rather than a storage drawer, so it was a little difficult to get the lower tip of the spring back into that hole. It actually ended up being easier to get the lower tip of the spring back into that hole first, before trying to reattach it to the hinge arm. Once I got the lower end into that hole, I pulled up on the spring and maintained upward pressure on the spring while I fiddled around to get the upper end into the hinge arm hole. Took about 20 minutes, door works perfectly now. Lots of sharp edges inside the oven, so had to be careful.

0) Unplug oven and shut off gas at the valve behind oven.
1) removed oven door (no tools required)
2) Removed enamed steel oven bottom (2 thumbscrews, push back, pull out)
3) Removed base panel on outside of oven (some might have a warming or storage drawer)
4) From bottom, removed heat shield to allow access to unders ... Read more ide of igniter -- 4 sheet metal screws, use 1/4" nutdriver
5) Now you should see all of the igniter, along with its wiring. One lead goes to a spade lug, the other uses a white nylon connector. Unplug igniter.
6) Using 1/4" nut driver, unscrew igniter from below. This is probably the toughest part of the job.
7) Once igniter is removed, put the bad igniter and the new igniter side by side. The leads on the replacement igniter are probably not going to be long enough (I ran into this), so clip the leads from the old igniter at the bas of the igniter and splice into the leads from the new igniter. After stripping the lead ends, I used a barrel splicer, but a wire nut or an inline splice with some heatshrink tubing or cloth electrical tape should also work fine.
8) Reverse steps above to install.

The igniter apparently controls the gas flow, so if the igniter doesn't get hot, the gas won't flow. In other words, be careful, but don't worry too much about having to worry about gas leaks, etc. In the end, it wasn't all that difficult, but I'm pretty good at home repair stuff. If you have a hard time plugging in a toaster, you should probably call a repairman.

Pull oven door open about a couple of inches. Grab the door by the sides and pull up to remove from the hinges. Set it aside. Remove the storage drawer under the oven. This gives you access to the tension spring attached to the hinge. Detach it by hand. Using a phillips head, unscrew and remove the damaged hinge. Replace the new hinge. Re ... Read more attach the spring. Replace the storage drawer. Replace the oven door. Done.

As has been said shut down unit,Breaker fuse.If you do not have install info.Get a copy on line. If you have another set of hands it would not hurt.! this has been stated before. Remove door, Remove 4 screws , to slide unit out,I used a saw horse with some cribing secured to the horse to get height, Pull the oven out so that the two fron ... Read more t supports are on the saw horse,and the back two are up to the edge runner.I used about a 1 ft stool for working height. Remove the top elec. cover sheet metal 2 screws. You will see were the wireing runs down the back. Get a small mirror,and flash light. Look down the wire opening in the back, you see the sensor connection ,I made a hook out of a coat hanger to grab it with. Pull it up before you disconnect it ,tie a piece of string to the sensor side of the connector , use 2 Ft. then disconnect remove two screws from inside the oven. And remove,sensor tie string on to new sensor connector pull through and connect.on top.Then replace everything cck every thing Twice!Doing this i didn"t have to pull the unit all the way out! LATER GOOD LUCK!

I removed the unit from the wall,removed the back panel to access the wires to the sensor,cut the plug off of the new sensor and strip the wires back,used the wire nuts to attach the new sensor,put all back together and slid back into the wall and works excellent.

After receiving the part ordered in one day, I removed the racks and the bottom flame spreader. The igniter assy. is held in by two screws, which only took a minute to remove. I removed the ceramic wire ties from, the old igniter and wire tied in the new one. Put everything back together and tested the oven. It works great again. Thanks f ... Read more or the quick response and delivery.

First I removed the pan drawer. Then I removed the metal cover under the stove. Not sure if you have to remove that or not. I think I could have left that on. I then looked inside the oven and removed the two screws in the back to remove the lower cover. Ahh, the hot surface ignitor and flame grill exposed. I then turned on the oven again ... Read more to make sure the hot surface ignitor was not glowing. I went back underneath, and disconnected the hot surface ignitor. I followed the wires from it to where it was connected. I then unscrewed the 2 screws that held the flame grill in place. Next, I went back in the oven and removed the flame grill with the hot surface ignitor still attached. I then unscrewed the hot surface ignitor and replace it with the new one. Key points: make sure you mark which wire had which connector, or only cut one at a time. Also, they do not come with new clips, so don't cut you wire too short. I then fed the wires and the base of the flame grill back down the slot, rescrewed the flame grill to the oven, attached the wires, and turned on the oven to make sure it worked. I finally replaced the lower plate inside the oven, the lower plate under the oven, put the drawer back in and I was done.

It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

First remove the broiler drawer. I laid on my side and reached into the oven to do the work, I first removed the one screw holding the splash plate (in the rear) and lifted the plate out. Then, removed the two screws mounting the ignighter to the burner base. Cut the wires on the old ignighter about half way between the connectors on t ... Read more he safety valve and the ignighter. I used a utility knife to strip 3/8" of the insulation on the wires still connected to the valve. Then, mount the new ignighter. Route the ignighter wires behind the gas tube. Use the enclosed ceramic wire nuts to connect the new ignighter wires to the wires still attached to the valve. Push the wire nuts into the hole behind the valve. Reinstall the splash guard and broiler tray.

I've been searching for new drip pans for my very old Kenmore gas stove for over 5 years, and this is the first company to give me the specialized help to find them. Kenmore drip pans for my model are made by another company, which I did not know, and the customer support rep also was helpful in telling me how to measure the stove openin ... Read more g to get the right size. The price was very reasonable, the installation took 30 seconds, and I am again happy to look at and use my stove. I will make future part purchases at PartSelect. Thank you. J Ahrens