91133213101 Kenmore Cooktop - Instructions

I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.

I've replaced 2 igniters on this stove. My symptoms were that when I tried ... Read more to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

Pulled the old one out. Disconnected the wire. Repaired the frayed wire cover with Liquid Tape. Connected the wire. Inserted the new part into the hole. This is after installing a new spark module earlier. But that was dumb easy too. So for about $100 bucks in parts and an hour of my time I saved myself the appliance repairman money and ... Read more agonizing scheduling and dealing with them for the price of gold. I also replaced all the gaskets on the burners in that time. It so easy even a financial planner could do it.

I removed the burner head #152 and the Burner Cap #330, no tools are needed to remove these items. I pulled the igniter up far enough to get to the wire, disconnected and connected the new igniter put it back in place, reassembled the two parts plugged it back in and turned it on and it worked.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on the ... Read more m, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. ... Read more I used new gashket and ignitor.

Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.

First take picture of cooktop. Go below cooktop and unplug electrical and turn off gas valve. Set burner greats aside along with bummer caps. Pull control knobs straight up and off, and set aside. Use 15 torque driver and remove two torque screws from each burner bases. Pull each white igniter up while holding the burner base in plac ... Read more e. There is a wire attached to each igniter, separate the wire from the igniter and set aside. Once all igniters are removed, carefully remove all burner bases and set aside. Now lift top cover off. As you’re lifting the cover careful of the igniter wires. Now take another picture to refer to when installing new igniter harness. Notice where the harness plugs in and use pliers to remove the two plug connections from the igniter module. Then remove the rest of the harness from the top of the gas valves. Vacuum debris and clean up tray. Your last photo will be handy, refer to when installing igniter harness. Orient. All burner igniter switches the same on each gas valve. Check for wire clearance on wire harness. Reinstall top, guide igniter wires up through top, relocate burner bases in correct locations. Start all torque screws, leave loose until all igniters are reconnected and placed back down in there holes. Then tighten all torque screws. Reinstall burner caps, control knobs, and greats.
Go underneath and plug in power cord and turn gas valve on. Check all burners for correct operation.

It's a very simple repair all you do is unplug the stove top remove the burners tops lifting them straight off you'll find two screws on each of them unscrew the two screws lift them off and set them aside you should find gaskets under each one of them ours was not in very good shape at all most were missing lift the top off of the stove ... Read more top you'll find the wires with a white I believe one was rectangle and the rest were square pieces just pull them straight up you have to give them a little bit of strength to get them off on our stovetop that were five on one wire 1 to the next of a night so on at the end there are two plugs unplug them pull the one straight up you might need a needle-nose plier and the other one is connected to another wire you just pull them apart hands on each one have the new set ready in the center of each of the square white pieces you may have to turn the little piece in the center to line it up with the flat part push them down they will seat firmly put the top back down screw the burners back in place put the burner caps back on plug the stovetop back in and turn it on.

Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

Remove burner, replaced gasket and spark igniter. On bottom of grill replaced missing rubber foot protectors. Initially I thought I would have to splice into the igniter wire however, after watching the video on repair, I discover all I had to do was carefully pull the wire out of the igniter from the bottom and push the wire into the b ... Read more ottom of the new igniter, then replace the burner into position and tighten the trox screws. It was a simple repair and everything is working fine.

Cut off approx. 1/8" in length for correct fit.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

I needed a right front burner injet which is no longer made. On my cooktop I was able to move the left burner to the right and then ordered the left. Very easy to replace.