91133204101 Kenmore Cooktop - Instructions

I removed the old igniter by working a thin screwdriver under the edge of the igniter, and carefully prying it up. I then used pliers to pull off the electrical wire. Connected up the new igniter, and pushed it back into the hole. A very simple repair.

I've replaced 2 igniters on this stove. My symptoms were that when I tried ... Read more to light one of the bad burners I heard clicking, and could see the spark on the other (working) burners. So I knew the basic sparking function was working. Just that the igniter on the broken burner would not spark.

A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.

Pulled the old one out. Disconnected the wire. Repaired the frayed wire cover with Liquid Tape. Connected the wire. Inserted the new part into the hole. This is after installing a new spark module earlier. But that was dumb easy too. So for about $100 bucks in parts and an hour of my time I saved myself the appliance repairman money and ... Read more agonizing scheduling and dealing with them for the price of gold. I also replaced all the gaskets on the burners in that time. It so easy even a financial planner could do it.

Repair to range went real well, Lifted range from

counter. Removed eight screws that secure burner

assembly. Lifted burners from it's position, and

removed igniters. Installed heat srink at burner

connections so as to ensure high voltage would

have no leaks. Removed insulation, and ... Read more installed

spark module.. Reassembled unit, placed in

counter cut out, put 110 volt cord into outlet.

Tested all burners, everything worked great..

The repair took about hour and 15 minutes.

Have fun and be careful...... THE END

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part onl ... Read more y coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

I removed the burner head #152 and the Burner Cap #330, no tools are needed to remove these items. I pulled the igniter up far enough to get to the wire, disconnected and connected the new igniter put it back in place, reassembled the two parts plugged it back in and turned it on and it worked.

I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on the ... Read more m, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!

First I removed two screws holding head in place and carefully lifted assembly up using flat screwdriver. I separated old igniter from feed wire with gentle pull. I reversed assembly after cleaning old gasket residue. torque screws back in place after cleaning with small ss wire brsh in dremel tool. Tighten in steps to firm light touch. ... Read more I used new gashket and ignitor.

Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.

Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.

I do use silicone to help hold the foot but it still won't hold

Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.

Remove burner, replaced gasket and spark igniter. On bottom of grill replaced missing rubber foot protectors. Initially I thought I would have to splice into the igniter wire however, after watching the video on repair, I discover all I had to do was carefully pull the wire out of the igniter from the bottom and push the wire into the b ... Read more ottom of the new igniter, then replace the burner into position and tighten the trox screws. It was a simple repair and everything is working fine.

Cut off approx. 1/8" in length for correct fit.

Replaced Spark Module and adjusted igniters

I needed a right front burner injet which is no longer made. On my cooktop I was able to move the left burner to the right and then ordered the left. Very easy to replace.