9112WUT Magic Chef Range - Instructions

i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace

First off...there are 2 possible oven igniters for this model, and you must determine which one you have. Remove racks from oven.Remove oven door. There are 2 latches(tabs) on the oven side of the hinge.Pull these forward and down. Close the door approx. half way and it will lift straight up. Carefully lay the door aside.There are 2 Phill ... Read more ips head screws at the rear of the pan. They are steel, and may be rusted in place. I used a Dremel with a cutoff wheel to cut a slot in the top of the screw. Then I used a straight blade screwdriver with a pair of pliers on the shaft to assist removing the screws.The oven pan lifts up at the rear to remove.Use a nut driver to remove the 2 screws holding the igniter. Mine were stripped.They use a machine thread in light gauge sheet metal. Then use an air ratchet to put them in. Take a trip to the big box store and get some short stainless sheet metal screws to replace the damaged screws.Pull the wire through the insulation, unplug the old igniter and plug the new one in. Fish the plug and wire back through the insulation. Attach the new igniter with the new screws. Replace the pan with new screws, and reverse the procedure to install the door. Even with the purchase of the Dremel, you will still save a chunk of cash, and you get a tool for the arsenal. It's rare when you don't encounter some problems, with any job. The secret is not burying yourself with more problems you create.

Hello,

Your website and prediction that this replacement part was the problem were exactly correct. This part was easy to remove and replace, it is the starter for the oven so it comes with a heating element and a built in connector. I simply pulled the old wires up, unhooked the connector and removed the two mounting screws ... Read more . Plugged in the new part, pushed the connector back down past the insulation, re-installed the screws and turned the oven on and poof, it started up again. We have also noticed that the oven stays hotter now, just like it did when we bought it.

Thank you very much for the advice and for supplying the correct part. A $65 part is much better than having to buy a $500 new stove/oven. We are very happy we found you and will use you again should some other appliance break down.

Sincerely,
Jim Arao
Seaside, CA 93955

Got the part, changed it, works great. That's all

unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expec ... Read more ted.

used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.

took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the ... Read more hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.

Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I r ... Read more emoved the broken section of the screw.

I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom o ... Read more f the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!

I replaced the igniter.

Removed oven bottom. 2 screws and igniter was removed. 1 screw for back panel unplugged igniter.

Open the oven door, take the bottom out. The ignitor is right there!! unscrew it and unplug it... plug in and screw in the new one! Took about five minutes!! Our oven worked again after not working for a year!! Yeah!!

I called the yellow pages repair man and he quoted me $450 to replace the igniter. I did it myself for $63 and it took 10 minuet's. I'm gonna get a T shirt that says "Mr Fix It" Next is the refrigerator door gaskets! Someone from part select had mentioned that to take the door off the oven you "just open the door a little and lift it ... Read more off". that was a helpful hint because I would have been looking for screws for half a day!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

removed oven door and shelves and lower pan and replaced igniter