9000BL Makita Angle Grinder - Parts

This is a genuine manufacturer-approved replacement part, it is specially designed for use with Makita power tools. This screw is a standard hardware which has multiple applications depending on your tool, please refer to appropriate diagrams for correct location and use of this item. It is a high-quality pan-head screw with a washer and it is sold individually.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This genuine Makita replacement part is designed for use with a variety of power tools. This screw is a standard hardware which has multiple applications based on your tool. It is made out of metal and it is sold individually. Would require a screwdriver to install or remove this screw.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This Trigger switch has 4 terminals and a locking mechanism for the switch. This genuine Makita replacement part is sold individually. Switches are commonly replaced parts in tools. A switch handles on/off and variable speed operations. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because...Read more switches use mechanical internals, they will degrade and wear out over time, eventually needing replacement. Some common signs of a broken or failing switch are as follows: • The tool has completely stopped functioning • it will not start. • The tool operates intermittently, requiring multiple tries to turn on, until eventually it won't start at all. • The variable speed function and electric braking aren't working properly.

This cord guard / strain reliever is a genuine Makita replacement part. It covers the final portion of cord before entering the tool, providing extra rigidness and preventing cord damage. Over time these cord guards break down and require replacement. The guard is constructed of heavy duty rubber compound for toughness. This cord guar...Read mored is compatible with the tools listed below. It is not guaranteed to fit any other power tool models.

This genuine OEM woodruff key is a small, semicircular metal piece used in various power tools to connect rotating parts, such as shafts or gears, to other components like wheels or pulleys. It prevents slippage between these parts, ensuring smooth synchronization and power transmission. With a width of 3/32 inches and a length of 5/8 inc...Read morehes, consider replacing a woodruff key if you notice misalignment or excessive movement between the connected parts. Be sure to inspect the key for signs of wear, damage, or bending. Removing the key depends on the make and model of your tool. If the key is visible, gently tap it from one side using a small hammer and a punch or drift pin. This will dislodge it from its slot. If the key is stuck or difficult to access, you may need to partially disassemble the tool to gain better access to the key. Once the key is loose, carefully pull it out using pliers. Clean the keyway and slot before installing the new key. Before making your purchase, remember that this component is sold individually.

This authentic component is supplied directly from the original equipment manufacturer for use with Makita grinders. It is an identical replacement for a missing or a faulty pin that was installed on a new unit. The pin helps to secure the compression spring, please make sure to check appropriate diagrams for the correct location and use ...Read moreof this hardware. Keep in mind this high-quality part is made of durable metal and is sold individually.

This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it has multiple applications based on your tool. Please refer to diagrams for correct application.

This replacement side handle grip is specially designed for use with Makita power tools. It is an authentic high quality item that is sourced directly from original equipment manufacturer. This is the side handle that provides a safe and stable grip for your tool. Please note, this plastic grip is sold individually. No tools would be needed to replace this item. Simply screw it in the threaded opening on the housing.

This is an authentic OEM part. The Makita compression spring 7 is made for use with several router and grinder devices. The metal spring is often fitted in the motor bracket, providing tension to the pin. This component is sold individually. Please refer to the specific manual for repair instructions. No tools should be necessary for making the installation.