- Home
- 8TWTW6000JW0
- Instructions
8TWTW6000JW0 Whirlpool Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hub had warn its grooved teeth off and washer wouldnt agitate
66 of 93 people
found this instruction helpful.
-
Allison from RICHFORD, NY
- Easy
- 15 - 30 mins
-
Screw drivers
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more
it back up and got caught up on laundry. good day when the washer is fixed.
Read less
Was this helpful?
Thank you for voting!
Waher would not spin and made noise
25 of 29 people
found this instruction helpful.
-
Andrew from SYLVANIA, OH
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install
... Read more
and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Read less
Was this helpful?
Thank you for voting!
latch switch was not working
28 of 43 people
found this instruction helpful.
-
John from BEAVER DAMS, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
unfasten top from back, slide top forward and lift up, remove switch and cable (one piece), in stall new switch and cable, put top down and slide back, reinstall screws.
Was this helpful?
Thank you for voting!
Screeching noise when starting the washing cycle. Especially with heavy loads.
15 of 19 people
found this instruction helpful.
-
Armando from UNION CITY, CA
- Really Easy
- Less than 15 mins
-
Socket set
The belt in this model is underneath the washing machine. Disconnect water lines and power cords, set up the drain hose in a bucket to avoid water spilling on the floor, tip the washing machine on its back, remove two bolt screws holding the plastic covering the belt, remove the old belt, and install the new one.
Was this helpful?
Thank you for voting!
Worn out splines connecting transmission driveshaft to agitator.
13 of 15 people
found this instruction helpful.
-
Thomas from MILLBURY, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
DIY'er working on a Maytag Centennial type washing machine should be aware that replacing a a transmission or agitator due to worn out splines is only half a job done well. I originally replaced my transmission due to worn splines, only to discover later that the worn agitator splines caused the new transmission splines to wear out at an
... Read more
accelerated rate. Transmission and Agitator should be replaced together, along with a new Agitator mounting bolt. There are plenty of video's online of how to do this repair so I won't get into that here. Just wanted to drop the above sage advice. Transmissions for these washers aren't cheap.
Read less
Was this helpful?
Thank you for voting!
Whirlpool builds junk lid switches don't lasting when you have suffered water! About every 3 months it goes out! Repairman won't come to fix so I do it myself!
13 of 17 people
found this instruction helpful.
-
Charlie from OAKWOOD, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplug washer
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash
Take back panel off
Un plug lid switch
Take screwdriver snap out switch
Snap in New switch
Plug it in
Replace back panel plug in washer
Wash
Was this helpful?
Thank you for voting!
The tub would spin but it was weak. The splines were stripped on the drive hub.
11 of 12 people
found this instruction helpful.
-
Doug from EAU CLAIRE, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Pulled the agitator, un-screwed the drive hub, cleaned the splines on the transmission, vacuumed the debris out of the tub. The repair video said to put towels or something down in the tub so if you drop a screw it will catch it. Put it back together and re-calibrated it. It didn't want to go into the calibrate mode until i moved the mode
... Read more
switch all the way to the left and then right first. Good quality factory parts!
Read less
Was this helpful?
Thank you for voting!
FAULTY LATCH-WASHER WOULD NOT GO INTO SPIN MODE
11 of 14 people
found this instruction helpful.
-
EVAN from STOCKTON SPGS, ME
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
THE NEW LATCH COMES WITH A NEW BEZEL ATTACHED, WHICH MOUNTS TO THE TOP OF THE WASHER, JUST UNDERNEATH THE LID. BECAUSE THE ORIGINAL BEZEL WAS IN PERFECT CONDITION AND DIFFICULT TO REMOVE, I DECIDED TO REMOVE THE BEZEL ON THE NEW LATCH, AND USE THE ORIGINAL ONE. THIS WOULD HAVE TO BE DONE REGARDLESS IN ORDER TO INSTALL THE NEW LATCH. REMO
... Read more
VING THE BEZEL WAS DIFFICULT DUE TO ALL THE LOCKING TABS THAT KEEP IT IN PLACE. I HAD TO RESTRAIN THE SLIDING SWITCH PARTS WHILE I REMOVED TO BEZEL TO AVOID THE ASSEMBLY FROM COMING APART. ONCE I SNAPPED THE NEW LATCH TO THE EXISTING BEZEL, THE ASSEMBLY WORKED FINE. TAKE TIME TO STUDY HOW THE LATCH ASSEMBLY IS ATTACHED TO THE BEZEL SO THAT YOU DON'T BREAK SOMETHING. USE A VERY SMALL SCREWDRIVER TO PRY BACK THE PLASTIC TABS IN ORDER TO RELEASE THE BEZEL FROM THE LATCH ASSEMBLY.
Read less
Was this helpful?
Thank you for voting!
replaced drain hose that was missing
12 of 20 people
found this instruction helpful.
-
Delmar from EAST TROY, WI
- Really Easy
- 30 - 60 mins
-
Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
Slow Spin Cycle with Fast/Normal Agitator
8 of 8 people
found this instruction helpful.
-
Michael from AURORA, CO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Socket set
My spin cycle was running, but spinning slowly and not drying my clothes. The agitator spun quickly like normal, but the basket did not spin fast. It seemed like something was slipping. I checked the belt, but it seemed fine and it was less than a year old. I was afraid that the transmission was going, but there wasn't any grinding sound
... Read more
of gears. Luckily the hub part description said that this could fix the slow Spin cycle. Over all the repair was easy, but pulling the agitator off was very difficult. I've got a strong grip and patience and after about 10 - 15 mintues of yanking on the agitator it came off. Don't try to use pliers as it will damage the plastic agitator. Replacing the hub drive and reassembly went very smoothly. The old hub drive wore out because it is plastic and connects to the metal drive shaft from the transmission. After years of torque, the hub will eventually strip out. Sooner depending on your usage and heavy duty cycles. In case you don't know, your machine might have the service manual in it on the inside of the body taped to the side. Mine helped me run through some troubleshooting steps and component tests to pinpoint to problem. Thanks Parts Select!
Read less
Was this helpful?
Thank you for voting!
drive hub splines were warn off. Thus no agitation was possible. Coins from laundry probably made increased friction to cause excessive ware on the splines.
8 of 8 people
found this instruction helpful.
-
Wayne from HILTON, NY
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
Force the thin nylon strap around and down into the perimeter of the agitator. Draw it snug to the center. The strap must be long enough to make a complete loop up to the top of the tub. Insert a fairly stout wooden stick through the loop so that an upward prying motion of the stick applies a vertical force on the agitator. While the
... Read more
force is applied pound on the lower part of the agitator so that it will break it free from the motor's axel. Of course remove the center bolt first after removing the small hub cover.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Applying liquids to the connection did not help. Just a steady upward force and a few rubber hammer blows to the lower part of the agitator di the trick.
Read less
Was this helpful?
Thank you for voting!
Water would not stop flowing.
8 of 9 people
found this instruction helpful.
-
melinda from HARROGATE, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
*be sure to turn water off, unplug machine, and unscrew the water hoses from the rear of the washer.
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
1. Removed screws from the back of the washer, just the top part where the controls are.
2. Removed the panel.
3. Use a putty knife or screw driver to pop off the top panel.
4. Remove the screws from the inlet valve.< ... Read more br />5. Unplug the wires connecting the inlet valve to the washer.
6. Lift out the old inlet valve.
7. Replace with the new inlet valve.
8. Plug the new wires into the washer.
9. Replace the screws in the inlet valve.
10. Replace the top.
11. Replace the rear panel and screws.
12. Reconnect the water hoses, careful not to mix the hot and cold.
13. Plug the machine back in and you're finished!
Read less
Was this helpful?
Thank you for voting!
During the Spin cycle the washer was noisy and moved around
8 of 9 people
found this instruction helpful.
-
JOHN from HERNANDO, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no
... Read more
tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!
Read less
Was this helpful?
Thank you for voting!
After removing the bolt on top of the agitator, it agitator was very difficult to get out.
7 of 7 people
found this instruction helpful.
-
John from SALEM, VA
- Very Difficult
- More than 2 hours
-
Screw drivers, Socket set
I watched the repair video on Partselect, it was very informative. In the video the agitator lifted right out easily, I was not so lucky. It took me and another gentleman about 4 hours to get the thing out. I watched other videos on ideas to remove, still no luck. Finally I cut the strap off of a carry all bag and was able to get it in a
... Read more
round the agitator and slide it under it. After getting it under the agitator we were able to pull up on it and get it loose.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.
The rest of the repair was simple, cleaned everything, installed new part, and now washing machine is working like new again.
Read less
Was this helpful?
Thank you for voting!
Washer would not complete cycle, as I forced the top open when locked
7 of 8 people
found this instruction helpful.
-
Louis from MANDEVILLE, LA
- Really Easy
- 30 - 60 mins
-
Screw drivers
I did the repair just as the video showed, and had no problems at all.
the hardest thing I had to do was to move the washer out to where I could get to the back of the machine.
Due to the help of the sales rep and the video the repair was very easy
Thanks
Louis
the hardest thing I had to do was to move the washer out to where I could get to the back of the machine.
Due to the help of the sales rep and the video the repair was very easy
Thanks
Louis
Was this helpful?
Thank you for voting!