8ET14 Whirlpool Refrigerator - Instructions

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.

... Read more />1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.

7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis

ordered the parts ,defrost timer and bi-metal thermostat,assumed it would be more practical to replace both than take a chance . watched a video on how to disassemble the control panel and remove the the timer and the back panel of freezer for the bi-metal thermostat,very clear instructions provided .took about 25 minutes to replace both ... Read more parts and now is working properly again,,Thanks Again PartSelect for the fast service and delivery

Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.

Followed the video instructions.

Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric

I received the glass shelf in a very well protected cardboard box, removed the glass shelf from the box, and inserted it into the slot in my refrigerator! Fit perfectly.

Since the original drawer sides had broken off the repair was very easy. I threw the old one in the trash and inserted the new drawer in its place. The fit was perfect and I have had no issues at all. The delivery was rather speedy also. Very happy!!

The rental house I live in did not come with the original shelves for the Refrigerator. Had to strategically stack stuff on top of one another with locker shelves. Entered the model number on the site, order the best matching item, and the part that came was a perfect fit. I'll be getting another.

I watched the video that was included with my on line order, it was helpful, although different model shown . I would say it was not difficult to install, the enclosed instructions were a bit confusing.

The evaporator coil was fully coated with ice. When all the ice melted the 2 leads on the old defrost thermostat (which was defective -- the gel was protruding over the top of the thermostat) were cut and the old thermostat removed. The leads from the new thermostat (bought from PartSelect) were re-attached to the wires that were previous ... Read more ly cut and the defrost thermostat snapped back onto the evaporator coil.

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.