8852 - Parts

This high-voltage diode is designed for use within various makes and models of microwaves and is a genuine OEM part that converts alternating current (AC) into direct current (DC). If you notice your microwave turns on and starts but does not heat anything, this diode is likely responsible. You can check the continuity of the diode with a...Read more multimeter before outright replacing it, but it is important to remember that doing any repairs on a microwave and dealing with sensitive electrical components should be done carefully and with the appropriate precautions to avoid any hazards. To replace the high-voltage diode in your microwave, disconnect it from power and allow it to discharge. Using the appropriate screwdrivers, gain access to the control panel of the microwave. Using an insulated screwdriver, release any electrical charge in the capacitor by touching it across the terminals. Then you can remove any hardware securing the diode, including the harness connecting it to the capacitor, which may be easiest done with pliers. Connect the new diode to the capacitor terminal and the securing bracket, and then reassemble your microwave before connecting it to power again.

This is a mounting bracket for a microwave. The part is fitted between your microwave and wall to allows you to secure your appliance safely to the wall studs and install it above your range. It is made entirely of metal and has holes throughout the length of the part so you can choose to put screws where the wall studs are. This ensures ...Read moreperfect installation. The bracket measures 13 inches in diameter. Be sure to have someone help you secure the microwave to the wall. This is a genuine OEM replacement part. Hardware is not included.

This is a high limit thermostat designed for use within various models of microwaves. The purpose of a high limit thermostat is to open the circuit of the appliance when the internal temperature reaches a certain threshold, to avoid becoming a safety hazard. If this thermostat fails or is damaged, it will cause your microwave to stop oper...Read moreating entirely. This is not to be confused with a thermal fuse, which is a one-time use component, whereas this high-limit thermostat resets once it drops back below operating temperatures. But if your microwave has repeatedly shut off, it is defective, or if the manufacturer recommends you replace it after it is triggered, it needs to be replaced immediately for safe operation. Consider inspecting your microwave for other component damage or factors that could lead to your microwave overheating, because that is what is causing this thermostat to be triggered. Replacing the high-limit thermostat will require a flathead and/or Philips-head screwdriver to remove the cover for the electronics of the microwave. First, you will want to unplug your microwave from the wall outlet and use your screwdriver to remove the side/top cover to give you access within it. Using your user manual, locate the thermostat within the main panel assembly and disconnect it from the wire harnesses, which may require a set of pliers. Here you can inspect it and any other components for visible burn damage. You can also test this thermostat for continuity with a multimeter, to see whether it is burnt out or perhaps defective. Install the new thermostat in place and reassemble your microwave, and you can now microwave safely.

The microwave light, or surface light lens, keeps the bulb in your microwave protected from getting cracked, scratched, and damaged. If your lens is defective or broken, or the bulb in your appliance is easily getting damaged, replacing the lens can be a solution. Refer to the installation instructions provided by the manufacturer for fur...Read morether guidance. Remember to unplug your appliance from the power source before starting this project, and wear gloves to ensure your hands are protected as a safety precaution.

This genuine drive belt is an original replacement part sourced directly from the manufacturer and is commonly used in Craftsman lawn mowers and edgers. Made from flexible rubber, it transfers power from the engine to the pulley that drives the cutting blades. Over time, the belt may become brittle or cracked due to wear and exposure, req...Read moreuiring replacement to maintain optimal performance. Measuring 3L x 35.80 inches, this belt is sold individually. A wrench may be needed for installation, depending on your equipment model.

This part is the replacement flat bolt for your microwave. It is a Phillips-head screw, which is approximately 4 inches long. The main reason to replace this bolt is if your current bolt is stripped, damaged, or missing. This part is an authentic OEM part sourced from the manufacturer and is sold individually.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This vent damper is a genuine OEM replacement part that is compatible with various models of Samsung over-the-range microwaves with ventilation systems. It is responsible for regulating the airflow in the microwave venting system. When the microwave is not in use, the damper remains closed to prevent outside air from entering the microwav...Read moree cavity. However, when you are using the microwave, the damper opens to allow air and steam from the cooking area to be vented out. This helps to remove cooking odors, steam, and excess heat from the kitchen. If the damper is damaged, corroded, or worn down, it will need to be replaced to ensure efficient ventilation and maintain the air quality in your kitchen.

The flange sleeve bearing, also known just as the bearing, is sold individually, and assists the tine shaft rotation on your tiller by reducing friction between the moving parts and securing their positioning. Because of this function, this part can wear easily and requires regular replacement. This part is OEM, black in color and made of...Read more metal. If the shaft becomes loose within the tiller housing, and you notice noise coming from it, it is likely that you need to replace this bearing. Most customers rated this as a moderately easy repair, which requires a screwdriver, pliers, a socket set, wrench driver, and nutdriver.