8676431 Kenmore Heater - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Temperature setting not working
19 of 23 people
found this instruction helpful.
-
Robert from Buffalo, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!
NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use ... Read more the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use ... Read more the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
Read less
Was this helpful?
Thank you for voting!
No heat in dryer
10 of 14 people
found this instruction helpful.
-
Noah from Maiden, NC
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Took off the lower front panel, removed duct piece from filter to blower fan, removed two screws and two wires to thermostat in exhaust ducting, then replaced thermostat with new one. Very easy job and everything worked like new when I reassembled it.
Was this helpful?
Thank you for voting!
electric dryer stopped heating - the thermostat got very hot
4 of 8 people
found this instruction helpful.
-
Ignas from Midpines, CA
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find whe
... Read more
re they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.
1 person
found this instruction helpful.
-
Mark from BLOOMFIELD, CT
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.
Was this helpful?
Thank you for voting!
More Dry setting does not work
2 of 5 people
found this instruction helpful.
-
c from vestavia hills, AL
- Easy
- 30 - 60 mins
-
Nutdriver
Repair was not successful
Was this helpful?
Thank you for voting!
no heat
-
Dan from Thomasboro, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
ordered wrong limit switch had to reorder right switch and decided to replace the heater element as well. works fine now
Was this helpful?
Thank you for voting!
low or no heat
-
charles from bryan, TX
- Easy
- 15 - 30 mins
-
Nutdriver
Removed back cover of entire dryer.The thermostat was accessible from that point(Just as diagram showed), removed two wires from thermostat, removed thermostat & replaced with new thermostat & plugged 2 wires back in just as instructions indicated. Very simple,15 minute job. I will certainly use again for any appliance repairs.
Was this helpful?
Thank you for voting!
A lot of noise coming from the front of the dryer.
-
David from Kingston, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
After removing the front of the dryer it was evident that the blower boss had broken where the motor shaft comes through and is attached. I removed a few more parts to make the blower more accessible and removed it. I then machined a new boss and attached it to the blower and reinstalled it.I then did a quick continuity check on the three
... Read more
thermostats since the dryer was already apart.I discovered one was faulty and ordered a new one from you.That repair took all of five minutes.The irony of the whole thing is that while I was ordering the thermostat from you,I asked out of curiosity,if the blower was still available. As it turns out it still is but the new machined part worked out great and the dryer was back up and running in no time.
Thanks again,
Dave
Thanks again,
Dave
Read less
Was this helpful?
Thank you for voting!
Dryer Not Drying Clothes on first cycle
-
Thomas from Glenpool, OK
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Took the back off the dryer. Disconnected the old thermostat and installed the new thermostat. Connected the back of dryer. Put in a load of clothes to dry and the clothes were dry on the first try. Works like a new dryer. Saved a lot of money not having to buy a new dryer when all I had to do was replace some old parts.
Was this helpful?
Thank you for voting!
not enough heat to dry clothes
-
James C. from Cobbs Creek, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
always unplug from outlet first, unscrewed the back off and pull off the wire from cycling thermostat ,take the two screw out that holding it in place and replace the new one .Very simple and easy. Thank you for the easy step by step video to complete this repair. James
Was this helpful?
Thank you for voting!
Washer/Dryer would not start
-
James from Salt Lake City, UT
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
Neither the washer or the dryer of the stacked unit would start. The website suggested that one of the causes could be the thermostat. I ordered a replacement that arrived quickly. Swapping the part only took minutes, and it started just fine.
Was this helpful?
Thank you for voting!