86150-4 General Electric Freezer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Clicking sound then within a minute clicking again, not cooling.
81 of 97 people
found this instruction helpful.
-
Melvin from Semmes, AL
- Easy
- Less than 15 mins
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it r
... Read more
attles like a baby rattler then it's most likely the problem. Replace wires into the new relay and plug back into the compressor.
Read less
Was this helpful?
Thank you for voting!
Stopped working, cooling.
15 of 19 people
found this instruction helpful.
-
Jennifer from Jonestown, TX
- Easy
- 15 - 30 mins
-
Screw drivers
I used a small screwdriver to disconnect wires from old starter. I connected the overload and starter, two wires. I put the unit back in the keeper, plugged the unit in, turned up the thermostat and it's working beautifully.
Was this helpful?
Thank you for voting!
Freezer quit. Compressor would not start.
9 of 11 people
found this instruction helpful.
-
Steve from Neosho, MO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Like another post, the start relay rattled like a baby rattle. Replaced the start relay and freezer works great.
Was this helpful?
Thank you for voting!
mottor starts than stop.
9 of 11 people
found this instruction helpful.
-
Gilmar from Miami, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i f
... Read more
ound PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.
Read less
Was this helpful?
Thank you for voting!
While defrosting freezer tossed the drain plug with ice and water into the sewer system.
4 of 5 people
found this instruction helpful.
-
paul from LISLE, IL
- Very Easy
- Less than 15 mins
Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.
Was this helpful?
Thank you for voting!
food was thawing, water on floor from defrosting.
3 of 3 people
found this instruction helpful.
-
James from XENIA, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
removed the main screw to expose the cold control, checked for power at the 2 power terminals. no power. ordered new control and resolved the problem. easiest repair I have ever done.
Was this helpful?
Thank you for voting!
Not cooling at all.
3 of 7 people
found this instruction helpful.
-
Kathleen from Casper, WY
- Easy
- 15 - 30 mins
-
Screw drivers
Removed four screws and took out the old cold control and put in the new one. This saved me almost $250 dollars by doing it myself.
Was this helpful?
Thank you for voting!
awasome
-
chris from springfield, GA
- Really Easy
- Less than 15 mins
After reading reviews I was not sure but I ordered part on Wensday in the AM and I had the correct part Thursday evening this company rocks thank you by the way i paid for regular shipping I will order again in a heartbeat
Was this helpful?
Thank you for voting!