8565 - Parts

This screw is sold individually.

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

This screw is well under an inch long, and is made of metal.

This screw is sold individually. Size: 8-32 x 1/4 inch.

Model Number GB2526REKS : SCR

This part is sold individually. This nut can be found in various appliances including a dishwasher, air conditioner, washer, dryer, range/cooktop, oven, freezer, range hood, and refrigerator. There is a serrated pattern along the edge of the nut, which helps to avoid loosening while the appliance is in motion. Nuts may corrode or rust ove...Read morer time and will need to be replaced. You will need a wrench to screw the nut into place. This genuine OEM part comes directly from the manufacturer.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

This water tubing clamp keeps the 3/16-inch diameter water tubing mounted to your refrigerator. Its purpose is to prevent shifting, kinking, or loosening of the tubing, ensuring a consistent water flow for the water dispenser and ice maker. It is typically located at the back of the cabinet near the inlet valve. If the clamp securing the ...Read moretubing in your refrigerator is not properly secured, it can result in leaks or complete detachment. This poses a risk of water damage to your fridge, flooring, and nearby structures if not addressed promptly. To replace the clamp, refer to your user guide for its location. Then, use a screwdriver to remove the securing screw. Please note that this clamp is sourced directly from the original equipment manufacturer and does not include any additional hardware.

This 5/16 washer, or toothed washer, is sold individually. It provides a tight fit between the knob and the upper handle on a range of outdoor power equipment. It attaches between the wing knob and the upper handle, and over time and through use, can become damaged and need replacing. It is gold in color and metal, and repairing it is an easy task according to our customers.

This danger decal in your lawn equipment is a warning sticker that reminds users to keep their hands and feet away from certain parts of your machine. Measuring approximately 4 inches in both length and width, it has the message DANGER, KEEP HANDS and FEET AWAY written on it in English. Typically, this decal is placed near the dangerous p...Read morearts of your machine, such as its blades, discharge chute, nozzle, impeller, or dashboard. If the danger decal becomes worn, torn, or difficult to read, you must replace it as soon as possible to prevent accidents from occurring. You must place it in a visible location where the person operating your machine can see it and it needs to be near the part that it is warning them about. This OEM-certified sticker is sold individually.

This bolt is a genuine OEM replacement part used in a variety of lawn and garden equipment. It is 2 inches long with a head diameter of 5/16 inches, and a thread pitch of 16 threads per inch. The bolt is used to secure the upper and lower handles on your equipment. If the bolt is stripped or damaged, your handles will become loose and fal...Read morel out of alignment. You may also notice increased shaking when using your equipment. Replace the bolt promptly as the handles can eventually collapse. Each bolt sold individually.