8515 - Instructions

I used this part on a little, under-counter U-line ice maker that is the best little ice maker in the world. The single solenoid part from U-line cost more than twice as much as the generic GE one I ordered from you. It arrived in only 2 days and I was able to just remove the inlet and outlet line from the old solenoid and unscrew the bra ... Read more cket to remove it. I used the included bracket and one screw affix the new one to the ice maker, then just pushed on the inlet and outlet lines, tightened them on, plugged it back in and In about 20 minutes from start to finish, it was back in business, cranking out ice really quick as it was before. Could not imagine summertime in Texas without my U-line,,,Thank you!!!

I order another one thanks

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the cop ... Read more per refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Did the troubleshooting with online instructions and a multimeter. Bought the new thermostat. Disassembled the freezer compartment using a nut driver to expose the evaporator, etc. The thermostat was easy to locate in the upper right hand corner. The new thermostat had one wire that didn't have the correct connector on it so I stripped ... Read more the wire back and used a crimp connector and heat shrink to attach the connector from the failed thermostat. After plugging the new thermostat in I ran the refrigerator for 15 minutes to cool the thermostat and then rotated the defrost timer to the defrost position and tested the new thermostat. Reassembled the freezer compartment.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

Pretty simple really after reading online some other owners' experiences. This is a bottom freezer unit. Remove the ice maker, the tray slides, and the back cover of the freezer box. In my case I had to thaw it out with a hair dryer as the cover was frozen in place. I checked the old 'stat and found it was bad; I temporarily wired the le ... Read more ads together until the new 'stat arrived. It does allow the refrigerator to warm up during a defrost cycle but it beats de-icing it twice.The defrost 'stat is clipped over the refrigerant line in the upper right corner of the box. Resistance was 65k ohms and wouldn't close on low temp (tested by clipping it to an exposed refrigerant line in another upright freezer) but there was no obvious damage. The one lead on the replacement 'stat has the wrong connector so you have to cut off the original lead from the old unit and splice it on the wrong lead on the new one. I used an epoxy sealed heat shrink type butt splice. Reassemble and let it run. One word of warning: be careful tightening any screws as they will strip easily

First I removed the two screws that held the top of the handle in place. Then popped off the bottom holder. Replaced the broken handle with the new one, replaced the screws and snap on section and now have a nice looking refirigerator with a handle that works.

Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.

First I removed the ice catcher bucket to give myself a little room and lifed the ice maker lever to make sure it wouldn't try to produce ice while I was replacing it.

I removed the bottom screw and loosened the top two with a nut driver. The ice maker lifted right out and allowed me to disconnect the electrical plug; just sque ... Read more eze the little plastic levers on both sides of the plug and pull.

I plugged in the electrical connection from the new ice maker. Making sure the water spout was in place, I dropped the new unit over the two loosened top screws. I then replaced the bottom screw and tightened all three. I replaced the ice catcher bucket and made myself a martini as a reward for not spending the $75.00 to $100.00 for a service call.

Within a couple of hours it was again making batches of ice for more martinis; it was a day or so before there was enough for frozen Margueritas.

I never even unplugged the refrigerator or shut off the water supply, although I suppose it would be prudent but not necessary. Some people like me just like to tempt fate.

The repair was so quick I didn't even worry about emptying the freezer. It was so easy even a girl could do it ... no offense intended. At the equivalent of $300.00 to $400.00 per hour I wish I could do it all day. Maybe I should be a "refrigerator repairman".

Seriously, the only thing that could hamper you is a lack of confidence which will quickly be overcome in 10 to 15 minutes by a huge ego. That time frame includes locating the tools and taking a few deep breaths. Don't hesitate to give it a shot. If you can't do it you really don't deserve to have ice. It really is that simple and easy.

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

Opened mailer and bag and place the drain plug into the drain. fit perfectly. In fact it is better than the one lost since the original needed a screwdriver or tool to remove the plug. This one has a flang or finger turner on it so that it can be removed. Also, does not interfere with items in bottom of freezer.

Followed the directions in the package. Turned off the power, removed two screws following the directions and replaced the entire unit. So easy even a Cave Man can do it. No kidding, and the best part was the fact that our local distributed wanted almost $20.00 more for the same part and I'd have to drive over a hour 40 miles to get it.

Happen to locate your site by Google. Was impressed and really pleased to find a schematic and directions to find and remove and specs to test the water valve and Defrost thermometer using an electric multimeter. You cannot tell by "looking" at a component if it is still OK.
So I put all the freezer contents into my beach cooler. T ... Read more he repair went as follows.
1. Removed the 6 screws from the back panel and pulled it out of the way.
2. Located the defrost thermostat and pulled it off of the coil.
3. Pulled the two connections off and took it to the bench to test. It showed no readings indicating it was dead.
4. Ordered a new one which came in two days.
5. Had to change the electrical connections using wire nuts.
6. Reversed the process plugged the refrigerator back into the wall. It started and later on I was getting ice cubes.
A great experience. Don't mess with repair guy as they normally are not up to speed on all devices and you are paying for them to learn how to repair your appliance in several trips. Probably using this site. If you can follow instructions, you can do this stuff.
Note. I tested the Water valve using given instructions. More time is used moving things around than the actual repairs. I avoided $150.00 for a new ice maker unit.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ... Read more ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same t ... Read more ime to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.