85054442 Kenmore Range Hood - Instructions

Slide grease filter about 1/2 inch to right (or left) using the d-ring attached to one side and then pull down and out. Push charcoal filter frame slightly to rear and pry down from front. Install new charcoal and grease filters by reversing process. No tools - 5-minutes max!!

Removed old grease screens by sliding sideways and then pulling out of the grooves. (helps to have rubber gloves as the grease is slippery). Put pressure on the back of the charcoal filter rim and allow side closest to you to drop down slightly so you can get a fine flatblade screwdriver under and pop the filter out of the holder. Work ... Read more s same on both sides. Install new charcoal filters after cleaning the holder edges with soap and water and drying. Make sure charcoal filter is in the second set of holder grooves and snap in place. Replace new grease filters with the pull tabs down and facing the center. Slide the grease filter into the holder grooves a little further back than normal and (using the pull tabs) pull the filter back the other way until flush with the opening and in place. The top exit ports are removed by taking out 4 screws;however, two of them are attached to spring clips on the underside and it is easy to break off the tiny plastic ridges underneath. The other screws come out easily and the entire exit port piece can be removed and cleaned. To reinstall just snap exit port back in place and replace screws. If you have broken off the slender plastic ridges you can sometimes turn the screww a partial turn and engage what is left; if not you may have to put some rubber grommets or pieces to support the bottom and keep pressure on the exit port piece which is not locked by only two screws.

I dropped the grease filters ( two under the unit) and then removed the dirty charcoal filters. The new charcoal filters were then snapped into place and the washed grease filters were then put back. The entire job took about. 5 minutes. No tools needed.

Why a tenant would remove and discard the grease filters without replacing them is beyond me! But, I removed the filters from the package and slid them into place. Two minutes tops. I would like to add that I ordered these on Thursday afternoon, and I had them on Saturday; awesome customer service!

It was a simple replacement of grease filter and charcoal filter in microwave/hood combination. I did use a screw driver to pry out the filters, but otherwise no tools. It was easy and straightforward.

It took me time to remove the parts and suss out the issue, but the repair itself was EASY. A wire ribbon connected to the circuit board had gone bad. One Phillips head screwdriver, 7 screws, to get at the old one, pull it out, replace it with the newly ordered part. NO PROBLEM. Ladies, you can do IT!! You have the power!

both of the pieces have a tab that help remove the pieces. They slip right out and new ones are putin place.

I just put the new ones in place…They were the right size, therefore no tools or extra effort!

Used hands to slide filters sideways, till they could be pried out with screwdriver or bare hands. When new parts arrived, easily slide new filters into position. In hindsight, we did not need to replace grease filter. I was able to clean one of those with ordinary dish soap, warm water, and a brush.

just replaced the filters

Slid them out and slid them in. Best part - ordered them at Noon on the Friday after the 4th of July and they arrived at 12:10 the next day - standard shipping.

Not so sure this would qualify as "instructions", but I only needed a screwdriver because the "D" rings of the old vent filters broke off and I had to pry to old ones out. Keep in mind, I am mechanically disadvantaged and can barely change an A/C filter ... that being said, all I did for this order was input my Model number and PartSelec ... Read more t found the correct replacement part. I receive the parts super quick (faster than the other 2 purchases I did that day). The only bummer was the packaging ... super huge box for small tiny parts. Otherwise, I now know where to go for replacement parts. This project should be a "no-brainer" for most DYI's, so getting the right parts with just a model number was lifesaving for me :0)

Remove old filter & insert replacement filters

Remove the screws holding the bottom vent plate to the upper unit, using a Phillips head screwdriver. Loosen a front screw last, but don't remove it. While supporting the plate in one hand, unscrew the final screw with the other. Lower the front of the bottom plate - tabs in the rear will prevent the plate from falling out. Bend the o ... Read more uter tabs holding the old filters in place, to allow them to be slid out. Insert the new filters & bend the tabs back into locking position. Raise the bottom plate and finger tighten a front screw. Replace and tighten all screws. This is also a simple way to remove/clean/replace the mesh filters. I've pulled the D-rings off trying to slide them out from below.