8348A Frigidaire Dryer - Instructions

My local repair parts shop did not have the part in stock. Shipping was really fast, so I repaired the dryer in less time than it would have taken if I had let my local shop order the belt for me. Repair was simple, just unplug dryer, pry up the front of the top, remove 4 screws from the top inside of front panel, disconnect two wires f ... Read more rom door switch, pull front off, and slip belt around tub. Remove small panel on rear (2 screws), place belt around pulley and move tensioner in place. Reassemble front panel and rear panel.

First I removed two screws holding a bracket that keeps the two ignition coils in place and removed the wires to the two coils. I replaced the old coils with the new coils, re-attached the wires and re-secured the bracket. I also replace the door catch simply using a flat head screw driver to remove the broken catch and pushed in the new ... Read more catch. The Lint Screen is a simple replacement requiring no tools.

the catch on the door was worn and cracked.... so I noticed it could be easily popped out with a screw driver and when the new part came in the mail 2 days later, it was just as easy to pop back in with no tools required. Now the door stays shut really good!!!

first i removed the top -second I removed the two screws hold the front on - thrid I unpluged the wiring to remove the front - fourth I removed old part and cleaned off old glue -fifth I applied new glue and new part - sixth I reasembled - worked good as new

first I remove the top cover,then the front cover. Then slide in the belt. that it.

lifted the top panel, there were 2 screws to remove the front panel, then the coils were right there on the bottom left side. a screw or two hold the coils inplace. Then just unplug the old coils and plug in to the new coils.

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt w ... Read more ill release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

remove top cover, remove front of dryer, unscrew two #2 screws from gas valve coil hol down bracket. replace coils. reassemble dryer.. works great.. had already replaced the thermostate and flame sensor.. didn't change anything.. the coil set did the trick..

All I did was push the new part into the machine! So easy!

I unplugged the dryer. Undid the top by taking out 2 screws and mounts on each side of the back. There were two screws in the front panel that had to be removed. One on each side. Then I took the two wires off the killer switch on the door. Marking which was top and which was bottom. Then I removed the front panel. Then I undid th ... Read more e drum which had 3 screws in. I took out the drum to find the problem. I replaced the drum putting the belt on. Then I took off the back panel at the bottom of the dryer to get at the idler arm. Took off the spring and unhooked the arm. I put the new arm on and replaced the spring. I then put the belt on to the pulley and closed up the back panel. I put back the front panel. I put the top back on. I plugged it back in and turned it on and it worked!

Removed 4 screws from 8" service panel from rear of dryer removed panel
Removed 4 screws holding rear of dryer top, removed rear brackets. compressed spring retainers on front of dryer top, removed dryer top.
Removed 2 screws from inside of dryer front, removed dryer front.
Removed old belt, cleaned machine, installed new ... Read more belt on dryer drum, inspected rear service panel to insure belt had reached the drive motor.
Reinstalled front of dryer, being sure to hold drum up in position to match front panel..
Went back to rear service panel and installed belt on motor pulley and tension pulley.
Set top back on dryer, test ran dryer for short time to ensure all was functioning properly.
Installed dryer top, and brackets.
Installed service panel.

Removed rear inspection plate, removed pulley spring and one hex bolt, replaced in reverse order. Very simple removal and install for this. Glad to see that Part Select still had parts for this 22 year old drier.

1. Slid putty knife under each side of front of dryer to release lid.
2. Removed 2 screws from front of drum to release door assembly.
3. Removed wires from door switch.
3. Cleaned lint out of inside of dryer.
4. Removed old felt seals, upper & lower.
5. Removed old glue with goof off type remover.
6. ... Read more Glued new seals on & held then in place with clothes pins. (there was enough glue in the tube that came with the upper glide for both seals)
7. Put dryer back together.
**Ensure you verify the correct felt seal pieces with the model number of your dryer, usually on inside of door.

First of all, check the feedback on your parts installation at partselect.com. You can learn alot and make the job that much easier. I simply popped the top lid on the dryer, remove the electrical connections to the front panel shut off, then removed the screws and popped the tabs for the front panel to install the new belt around the dru ... Read more m. I then opened the back louvered panel to loop the belt correctly around the pulley and proceeded to reinstall both the front and top panels. The lint screen is a simple two screw installation with little or no issues. Once installation was complete the dryer fired up and the drum began to spin once again. A simple repair done at a great savings!

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and ... Read more two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.