8339 Kenmore Refrigerator - Instructions

turn off water. turn off electricity. empty freezer section of frozen food. remove ice bucket. loosen two screws holding IM to wall of refrigerator. lift off icemaker, and then unplug it as you remove it. INSTALL new IM by: putting new water funnel onto new IM. attaching adapter cord to IM. plug in IM electrical cord to refrigerato ... Read more r and then hang the new IM onto the two loosened screws on the refrig wall. Now tighten the two screws. the extra adapter electrical cord hangs below the new IM, but does not get in the way when you reinstall old ice bucket. reload food, turn on elec and water. PS. i had a crack in the casing of the new IM, so i got a new one, but that one was cracked too. so i just installed the second cracked one. hope it is not a problem.

install icemaker water was allways delivered to previous unit water is not being delivered to icemaker still having difficulty

Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

Removed old ice maker, then screwed in new ice maker. Only thing that was a little difficult was to hold the auger motor, while trying to unplug the clipped in plug on the old ice maker. I could have used an extra pair of hands.

Instructions that came with the part were useless. I would have created new problems if I had attempted to follow the instructions. However, once I had the old part removed and put it beside the new part, required repair process was obvious, easy and quick. Frig now makes ice better than it ever did.

It was exactly as shown in your instruction video

Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could ... Read more need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord beh ... Read more ind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just ba ... Read more rely. But I'm back in the ice again, no dripping water, all is good.

Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.

I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrig ... Read more erators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.