826019 (Series A) Graco Sprayer - Parts

This is a genuine OEM approved replacement part designed for use with Graco paint sprayers. Due to heavy use or other factors, a cord can crack or become damaged. It is important to replace a damaged cord before continuing to use your equipment. This cord is made out of rubber and metal and is sold individually.

This authentic item is supplied directly from the original equipment manufacturer for use with Graco paint sprayers. The shield is made out of a durable material. When replacing this part a screwdriver might be required during the installation process. It will need to be replaced if it breaks. This item is sold individually.

This is a genuine OEM sourced part which is specially designed for use with Graco sprayers. It is an identical replacement for a missing or a faulty threaded deflector that was included with a new unit, please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of thi...Read mores component. Keep in mind this high-quality item is made of durable material and is sold individually.

It is an authentic component which is supplied directly from the original equipment manufacturer for use with Graco sprayers. This item provides an identical replacement for a missing or a faulty hose that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicat...Read moreion of this component. Keep in mind this high-quality item is made of durable materials and is sold individually.

This is the return hose assembly, or return line, which is designed for various models of airless paint sprayers and is sold as an individual part. The return line is designed to allow paint and pressure to be returned into the reservoir, and simultaneously connected to a specific port on the sprayer for a continuous paint cycle. This ret...Read moreurn line is comprised of a high-quality rubber and metal pump attachment at one end and a metal tube and plastic reservoir attachment at the other end. Depending on your model, you may need a set of pliers or a wrench to disconnect and remove the old line. Before you replace your old line, it is recommended that you wrap the metal end of the line with Teflon tape to create the best seal possible. When replacing the line, disconnect the sprayer from power and release any pressure in the spray gun by squeezing it until no more pressure is felt.

It is an authentic OEM supplied replacement part that is specially designed for Graco sprayers. This o-ring provides an air tight seal for the pump, please make sure to check appropriate diagrams for correct location and use of this item. Note that one durable rubber o-ring is included per order.

This connecting rod kit is supplied by the original manufacturer for use in paint sprayers. Each kit comes with the rod, pump pin and pump pin lubricant for your convenience. The connecting rod is found within the internal combustion engine of the paint sprayer where it connects the piston to the crankshaft. The connecting rod allows the ...Read morecrankshaft to rotate in order for the engine to run. Over time the rod can become worn down or damaged, causing loss of power and potentially irreparable engine damage. To remove the faulty connecting rod, you will need to disassemble the engine. Disconnect the faulty rod from the piston and the crankshaft, and attach the new one in its place. Ensure that it is properly aligned and reassemble the engine components to complete the repair.

This authentic manufacturer-supplied washer is specially designed for use with Graco sprayers. It is a special hardware that helps to provide a tight seal between connected components. This is an identical replacement for a missing or a worn washer that was installed on a new unit. One durable rubber part is included. Refer to the appropriate diagrams for your model to ensure the proper repair procedure.

This authentic OEM fluid filter manifold assembly acts as the main filter block for the manifold filter in your paint sprayer, ensuring that impurities are removed from the paint before it reaches the spray gun so that the debris does not affect your finish quality, damage your sprayer, or clog your spray tips. To check if it is broken, l...Read moreook for leaks or visible damage. Unfiltered impurities can cause clogs and blockages, leading to uneven or flawed paint application. To replace the assembly, first, set the pressure control knob to the lowest setting, turn off the machine, and disconnect it from the power source. Consult your user manual to locate the assembly, which is typically near the fluid inlet connection. Use a socket or wrench set to remove the components connected to the manifold assembly, including hoses, the transducer, the nipple, and the dump valve assembly. Unscrew the cap and remove the filter from the assembly. Please note that the replacement part is sold separately from the cap, insert, or filter.