825R - Parts

Discover the Ryobi Upper Drive Shaft and Housing Assembly designed specifically for line trimmers. With a shaft height of 25-1/8" this durable assembly is crafted to house and protect the drive shaft ensuring seamless operation for your trimming works. This genuine Ryobi item is engineered to not only withstand rigorous use but also provi...Read morede optimal fit and performance. To safeguard your hands and ensure a secure installation it is recommended that you wear work gloves during the assembly process. Trust in the quality of Ryobi for a reliable solution that ensures your line trimmer is working at its best.

The metal spring goes between the e-clip and the plunger and helps to maintain tension. It is a genuine item that is supplied by the original equipment manufacturer for use with trimmers. This is a small part that will need to be replaced if it becomes lost or stretched and may require a screwdriver to install the spring. This is available as an individual replacement part.

This is a high quality OEM supplied replacement hardware that is specially produced for use with lawn and garden equipment. It is a standard hardware that has multiple uses depending on the unit, please make sure to check appropriate diagrams for correct location and use of this screw. Please note one durable metal torx screw is included per order.

It is an authentic OEM sourced part which is made for use with handheld trimmers. This is the special component which provides a tight fit for the outer spool. Unfortunately, over time the hardware may get damaged or lost eventually requiring a replacement. One durable metal retainer is included. Refer to the appropriate diagrams for your...Read more model for the exact location and the correct application. You may need snap-ring pliers to perform this repair.

The Recoil Spring is a silver, metal spring which attaches inside the starter assembly. It is used to wind the rope back around the pulley after it has been pulled. If broken, the starter rope will not retract and the part must be replaced. This spring is rated "Medium" difficulty to install and will requires a screwdriver, pliers and a wrench set.

The Clutch Drum is a silver, metal part used to transmit power from the engine to the drive shaft. Installation is rated "Medium" difficult and will require a screwdriver, wrench set, and torx wrenches. This part attaches to the clutch assembly. If broken, the clutch will slip and you will lose drive power. If this happens, the part must be replaced.

This is a genuine item that is supplied by the original equipment manufacturer for use with trimmers. The metal clutch goes between the clutch drum and the clutch washer. It helps to spin the cutting head and the flex shaft. It may require a screwdriver and a hammer for installation. This clutch is available as an individual replacement part and comes with a washer.

This is an Genuine OEM replacement part used on Gas-Powered Handheld Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull th...Read moree starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor with Rubber Primer Bulb and Two (2) Rubber Fuel Lines. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.

This air filter and choke cover assembly is designed for small gas-powered outdoor equipment to protect the air filter and support proper choke operation. Made from durable plastic, it helps keep dirt and debris out of the engine intake while maintaining correct airflow for reliable starting and performance. It’s a simple, direct replacem...Read moreent for cracked, damaged, or missing covers to restore proper engine protection and operation.

This high quality OEM sourced replacement throttle cable that is specially designed for use with handheld trimmers. Throttle cable is connected to the carburetor and it stops the engine when you shift the lever to the full choke position. One durable rubber insulated metal cable is included per order.

This part is an OEM from the Ryobi manufacturer. The lower flexible drive shaft (24 3/4") is made of metal, and is compatible with multiple tools and machines. This part is used to operate the device cutting head, and is regularly secured in the draft shaft housing. It is recommended to refer to specific manual and diagrams for repair ins...Read moretructions. This part is sold individually. A screwdriver is often helpful in the replacement.