8236 - Overview

The tine thatching spring or thatcher attachment spring tine for your lawn mower attaches to the spring alignment rod and pulls dead grass and roots to the surface. This part is black in color and is made of metal. It is an OEM part sourced directly from the manufacturer and is sold individually. Be sure to wear work gloves when you are replacing the tine thatching spring.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs. This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

This driven ring is an OEM part direct from Snapper. The flexible plastic ring is compatible with many lawn mowers. This item is often fitted between the driven disc assembly and ring retaining plate, assisting the drive disc with propelling the mower. A screwdriver, wrench set, pliers are needed for the repair. This item is sold individually.

This is a original manufacturer sourced replacement part used on Snapper lawn mowers. This is the ground drive belt that connects the engine crankshaft pulley to the transmission pulley. This part is made out of rubber and it is sold individually. Clean the pulleys off before installing the new belt to ensure top performance and longevit...Read morey with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance. To replace this belt you would need a wrench and a screwdriver.

This replacement engine drive belt is a genuine Snapper item, not an aftermarket equivalent. It is supplied by original equipment manufacturer for use on lawn mowers. This belt helps to driver the mower. Over time belts tend to stretch and wear out requiring replacement. Please note, this rubber belt is sold individually. Replacing this drive belt will require a wrench set.

The Chute Plug is a plastic, black, individually sold part which covers the grass bag chute and is rated as "Easy" to install. This is an OEM part and if broken, it should be replaced. Refer to your make, model and diagram to ensure you've chosen the correct part.

It is a genuine item that is supplied by the original equipment manufacturer for use in walk-behind mowers made by Murray, Briggs & Stratton, Snapper, and Simplicity. The self tapping screw attaches to the front wheel drive rear baffle. A flat head screwdriver will be necessary during the installation of this part. Over time this part may...Read more become stripped and will need to be replaced. Keep in mind this part is made of metal and is sold individually.

This OEM hub cap keeps debris out of the hub and axle of your lawn mower. It is black in color, sold individually, and made of plastic. Over time, your hub cap may get removed or damaged due to fatigue and wear. If you notice it is missing or damaged, you will need to replace the hub cab. This is an easy repair that just requires the us...Read moree of a flat blade screwedriver for removal, and a rubber mallet for installing the new one inside the wheel hub.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.