8230 - Parts

Pilot Unloader Valve - Larger discharge port for 3-5 HP electric units without head unloaders.

Genuine Dewalt replacement part, it is sold individually. This is the spool that contains the cutting line for the trimmers shown below. It includes 20 feet of cutting line. When replacing the cutting line use .065 diameter line.

Keep in mind that this high-quality part is priced individually. The traction belt goes around the drive plate. A socket set and a wrench set might be helpful during the installation of this part. It will need to be replaced if it becomes stretched or broken. This is an authentic part from Snapper for use in snow throwers.

It is an authentic manufacturer-sourced component which is specially designed for use with Snapper and Simplicity snowthrowers. The purpose of this bushing is to help to secure the axle shaft allowing it to rotate with minimum friction. If the original item is damaged or is missing, this will provide an identical replacement. This part is...Read more made of high-quality metal and is sold individually. Check the owner's manual and the diagrams for your model to ensure the correct replacement procedure. A wrench set will be needed to perform this repair.

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering spindle and the front axle assembly. This item is sold individually, please note two washers may be needed.

This manufacturer-certified Grass Chute is a black plastic part used to direct grass clippings. Installation is rated as "Easy" by customers, and requires a wrench or socket. The chute secures to the top of the cutting deck. If broken due to wear/fatigue/damage you will be able to see the issue, and should replace the part. Refer to your make model and diagram to ensure this is the correct part.

This is a genuine OEM sourced replacement isolator foot that help to keep you air compressor stable and also help to minimize the vibration. This item is made out of rubber with metal and it is sold individually. Please note the screw used to attach it is sold separately. You would need a wrench to replace this item.

It is a genuine OEM sourced component which is specially designed for use with Murray and Snapper lawn and garden equipment. The purpose of this part is to provide a tight seal between connected parts, unfortunately, over time the material may wear out and begin to crack eventually requiring a replacement. Keep in mind this high-quality h...Read moreardware is made of durable nylon and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this thrust washer.

This authentic OEM sourced part is made for use with Murray and Snapper riding lawn mowers and garden tractors. It is one of the special pins which are utilized to secure components. If it is damaged or is missing, this will provide an identical replacement for the original component that was installed on a new equipment. This part is a s...Read moretandard hardware which may have multiple applications. Please refer to the appropriate diagrams for your model to ensure the exact location of this roll pin. One durable metal pin is included.

This is an original replacement part manufactured for use with Snapper riding lawn mowers. The woodruff key is used in the gear shaft on the chaincase and fits into the keyway on another part assembly to allow it to rotate with the gear. This woodruff key is available as an individual replacement part.

This hex center lock nut is sourced from the original manufacturer for use in lawn and garden power equipment. It is a hexagon-shaped fastener for bolts/studs that is responsible for the keeping the bolt/studs secure during use. The nut is made of metal and has a diameter of 5/16 of an inch and a thread pitch of 18 internal threads per in...Read morech. Over time the threads in the nut can wear down and the nut itself may crack or break. It is important to replace it as soon as necessary to avoid damaging your equipment. Use a socket or wrench to remove the old nut and thread the new one on. Make sure to order the correct number of nuts for your equipment as each nut is sold individually.

This is a genuine Craftsman replacement part that is sourced from the original manufacturer to be used with snowthrowers. The metal hex nut is commonly used to fasten the bolt that secures the height skid to the auger housing. This item is available as an individual replacement part, please note four nuts may be required.