82-1 - Parts

This is a door/light switch and it is a replacement part for your refrigerator. This part is activated as you open and close your refrigerator door. When the switch is activated and the door is open it will turn the light on inside your appliance, and when you close the door the switch will deactivate the light. Before purchasing this par...Read moret, you may test it for continuity to determine if your current switch is defective and needs replacing. This model is white in color and measures to be roughly one inch thick, almost two inches high, and almost 1.5 inches deep, with a male end plug.

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This cable barrel holder is a genuine OEM part that is designed for use with tillers and snow throwers. Sold as an individual part, this holder measures approximately 1-inch in length and is used to secure the clutch control handle and cable together. This holder is made of durable plastic and can replace the old holder by simply removing...Read more it, inserting the cable into the new holder, and tightening it until it is locked in place.?

The flange sleeve bearing, also known just as the bearing, is sold individually, and assists the tine shaft rotation on your tiller by reducing friction between the moving parts and securing their positioning. Because of this function, this part can wear easily and requires regular replacement. This part is OEM, black in color and made of...Read more metal. If the shaft becomes loose within the tiller housing, and you notice noise coming from it, it is likely that you need to replace this bearing. Most customers rated this as a moderately easy repair, which requires a screwdriver, pliers, a socket set, wrench driver, and nutdriver.

The Throttle Box Assembly, or the Throttle Assembly, is a kit that includes the housing, handle, and hardware. It is black and constructed of steel and plastic. It can be installed onto the right hand upper handle, using a screwdriver and pliers, and is rated as Medium difficulty to install. This kit contains the parts that control the ...Read moreamount of the air and fuel entering the engine. When the part breaks (likely due to fatigue) you will no longer be able to control the engine. If nothing happens when you move the handle, that means it has become disconnected. When the part is broken it must be replaced. Check your model number to ensure you are selecting the correct replacement part.

This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during the replacement of this item. It may become broken and will need to be replaced. This is an authentic Briggs & Stratton and Toro replacement...Read more part that is sourced from the original manufacturer for use with engines, snowthrowers, tillers, lawn mowers, and lawn tractors.

This OEM dust cap prevents dust from entering the shaft and surrounding area of your tiller. This part is black, sold individually, and made out of plastic. Due to damage from ongoing use, this part can become broken or get knocked off entirely and go missing, which you will notice, as it attaches to the outside of the tiller gear housing...Read more. This is an easy repair that only requires a hammer to make. Please note that you will need to purchase a rubber seal alongside the dust cap when making this repair, part number 921-0175.

The bearing seal, also known simply as the seal, is a special seal for the bearings in your tiller. It attaches in the tiller housing, with the bearing and shaft, and over time it can become damaged due to fatigue and general wear. This part is made of rubber, is black in color, and is sold individually. Repairing the bearing seal will ...Read moregenerally be a medium-difficulty job, one that requires a screwedriver, socket set, wrench set, and hammer.

The Jamlock Nut is a 3/8-16 inch metal nut which can be installed using a socket or wrench set. It's used to secure and lock parts in place. If the part is damaged and comes loose it should be replaced. This is an authentic part authorized by the manufacturer.

This authentic OEM bearing measures 0.62 inches inside diameter, and 1.38 inches outside diameter, and is 0.436 inches thick. Silver and balck in color and sold individually, the bearing is comprised of steel and rubber. This bearing allows the input shaft to rotate freely inside the gear box, and over time can become worn or damaged. Y...Read moreou will know your bearing is damaged if it is making a growling, grinding, or squealing sound. This is an easy repair, and requires a bearing puller tool to carry out. Locate the bearing inside the gear box on each end of the input shaft, ensuring you have confirmed this is the part you need by verifying your model number or using your owners manual.