8085C Kenmore Refrigerator - Instructions

installed new ice maker. Was very esay - the only problem I had was the length of the wire, due to the need to use the adapter, was hard to menauver around so that it didn't contact the bottom of the ice maker. Would be best if it was configured so that you had the right wire connection and didn't have to use the adaptor.

Turned off water, unplugged refrigerator, Removed defective unit with support bracket. Installed support bracket, adjusted flow screw per instructions, plugged in wiring with adapter, hung on screws, tighened screws, secured excess wiring harness (making sure it did not hang below icemaker per instuctions), turned on water, plugged in ref ... Read more rigerator. Comment it took a few hours to start making ice, air in line? After a couple of days seems to be working fine.

The repair took only 5 minutes. I removed the ice bin, which just slides out, then loosened 2 screws at the back-top of the ice maker. I then unplugged the broken ice maker, removed it, put in the new one, re-tightened the screws and plugged it in. It was making ice within an hour.

Loosened 2 screws, lifted icemaker brackets off of loosened retaining screws, unplugged electrical connector from the icemaker.
plugged in the supplied jumper harness & connected to the new icemaker, hung it on the loosened screws, secured the 2 screws.
Dranke beer & listened to my new icemaker rock & roll.
No further probl ... Read more ems, Frigie like new.
The price was the cheapest I could find. $78.00 total including shipping.
A little girl could replace this unit.

LOOSENED THE TWO SMALL SCREWS THAT HOLD THE ICE MAKER UP INSIDE THE FREEZER. DISCONNECTED THE WIRING HARNESS. TOOK THE OLD ICE MAKER OUT AND JUST INSTALLED THE NEW ONE IN REVERSE ORDER. LATER THAT DAY I HAD FRESH ICE FOR THE FIRST TIME IN WEEKS!

It was just a simple replacement, three nuts to loosen , a slight adjustment on the timer and reversal installation...As simple as replacing a light bulb! You needn't be a brain surgeon to do this job! Your installation video was very helpful....Thank you PartSelect Chuck McCann

The service man that I hired to fix my Ice maker removed the broken one. This is how I saw how easy it was to install. When the new one arrived all I had to do was plug it in then tighten 2 screws with the right size nut driver. This was the hardest part of the install havng the right tool for the job. Now I have Ice!

The repair was a simple swap of icemakers with a 1/4" nutdriver. I didnt get the first unit sent after 7 days, so I called PartSelect. They were very courteous and understanding. My icemaker arrived within 12 hours of my phone call! Excellent!

The screws holding the ice maker in place were backed out about a turn and a half or so. The icemaker was raised about 1/2 inch to clear the bolt heads. The icemaker was extended just enough to access the wiring harness connector. The connector was released, and the ice maker was removed. The replacement unit extension was unneeded. The w ... Read more iring harness connector was attached, and the wire was wire-tied out of the way. The icemaker unit was placed over the screw heads, rested in place and the screws were tightened (only snug). Easy-peasy!

was very easy. just ordered a new ice maker which was delivered in a few days. The installation was so simple. Just plugged the new ice maker in and hung the unit on the 2 screws. And then tightened the screws with a 1/4 in nut driver.

Turn off water, un-plug refrigerator, dis-connect water, un-screw bracket, remove valve and replace same way...Very easy

Fast and easy. Started by pulling out refrigerator and unplugging it. Water valve for ice maker was already turned off due to leaking. Disconnected old valve, detached old valve, reattached new valve and reconnected water lines. Bled the lines and turned back on. Make sure temp in freezer stays at recommended temps for ice making.

put in a new one

I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem

I watched the video and did the same thing on mine and now it is working fine