8085 - Parts

This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the l...Read moreimit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female,...Read more and one round male connectors. The tools you will need in order to make this installation include a 1/4-inch nut driver, and a Phillips screwdriver. Before starting this repair make sure to unplug your refrigerator and shut off the water supply.

This part is a solenoid-operated switch located at the bottom of the refrigerator. When the water inlet valve is turned on, water is released from the supply line through the water valve and into the compact icemaker mold. The kit includes the mounting hardware and bracket plastic tubing fittings. The retaining nut must be cut off the pla...Read morestic water line and gently pushed into the new valve. To remove, press down on the ring that the tube slides into. Refer to the installation instructions for further guidance. Please note: the manufacturer has redesigned this part and it can appear different than the original. It has a new quick connection.

The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pushes the cubes out and into the ice bucket, ready for the ice to be used. The outside diameter of this piece is almost two inches by two inches. The reason for n...Read moreeeding to replace your gear is if the current one is broken/missing a tooth, or if your icemaker is not dispensing ice and is noisy.

The ice stripper goes on the front of the ice maker and directs the ice cubes from the maker to the bin. Due to the frigid temperatures, the plastic breaks down and cracks from time to time. This may cause the ice cubes to get stuck in the ice maker and not dispense properly. You will need to open the freezer door, pull out the ice contai...Read morener by lifting and pulling out. Unplug the ice maker by releasing the locking tabs. Use your 1/4-inch nut driver to remove the screws holding the ice maker in place. Take the ice maker out of the freezer for easy access. The ice stripper can be removed by simply unlatching from the pin holding it in place. The new ice stripper should just click into place so the tab goes into the control head with ease.

This screw is sold individually.

This valve is intended for use with the ice maker in a refrigerator. The water valve supplies the water needed to make ice, so if your ice maker is not making ice or dispensing water, the issue could be that you have a damaged or faulty water valve. Before you decide to replace this part, turn the household water supply to this valve off,...Read more and remove the input tubing to see if it is clogged. If it is, clear the blockage to allow water back into the ice machine. Remember to disconnect the power and water supply to your refrigerator before beginning this repair.

This screw is sold individually. It is a genuine OEM replacement part, and it is designed for use with refrigerators. Most often it is used with the ice bucket ice deflector, retainer clip, and front cover. Due to varied uses we recommend referring to model-specific diagrams for exact placement. This screw measures 8-18 by 1/2 inch.

This is an ejector arm, and it is used in conjunction with your refrigerator. The function of this part is to act as a cube ejector inside your ice maker. The arm will rotate inside the ice maker to allow the ice cubes to fall out of the marker and into the ice bucket. This part is made entirely of plastic, is white in color, and has eigh...Read moret teeth. It measures just over 9 inches long, and one and a half inches wide. To make this installation the tools you will need include a quarter-inch nut driver, a flat-head screwdriver, and a Phillips screwdriver.

The micro switch in your refrigerator aids in the dispensing of ice and water. This micro switch controls the on/off function of the ice/water dispenser of your refrigerator. If you notice that your refrigerator is not dispensing ice or water properly, you may need to replace your micro switch. This part is made of black plastic, with thr...Read moreee metal prongs. The plastic portion of this part is approximately one inch in length. This is an OEM part sourced directly from the manufacturer. Be sure to unplug your refrigerator from the power source before you begin this repair.

This part is a one-time limit fuse used as a safety device. Once tripped, this part must be replaced.