EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

8060 - Overview

Models starting with 8060

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Charcoal Filter – Part Number: 5230W1A003A
$33.69
In Stock
Charcoal Filter
★★★★★
★★★★★
(16)
Part #5230W1A003A
This is an authentic LG charcoal filter for your microwave, sourced directly from the manufacturer. It is designed to remove odors from the air that circulate through your microwave vent. It measures approximately 11 inches in length, and 2.5 inches in width.
Air Duct Bracket – Part Number: 4810W1A151A
$17.15
In Stock
Air Duct Bracket
★★★★★
★★★★★
(2)
Part #4810W1A151A
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, and replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
Time Delay Fuse – Part Number: 3B74133Q
$11.77
On Order
Time Delay Fuse
★★★★★
★★★★★
(3)
Part #3B74133Q
The fuse-time delay may also be known as a line fuse or a microwave fuse, and it is a piece for your microwave. The function of this part is to shut off the microwave if there is a power surge, in order to protect your microwave from damage. You should consider having a service technician install this part as the high-voltage capacitors in a microwave can contain a very harmful electrical charge, even when the microwave is unplugged and has been inactive for some time. The tools that would be needed to complete this installation include a Phillips screwdriver, an insulated screwdriver, and a pair of pliers.
Halogen Lamp – Part Number: 6912A40002E
$21.45
In Stock
Halogen Lamp
★★★★★
★★★★★
(1)
Part #6912A40002E
This is a halogen lamp, or light bulb, for a microwave. The microwave light should illuminate the inside of the microwave while the door is open and while the appliance is running. If the light bulb does not illuminate, you may need to replace it. This part is sold individually. It is a common wear part and does not have a standard light bulb base, so consider ordering a spare. This part is made of clear glass. If the glass on the existing light bulb is broken, you may need to use a pair of needle nose pliers to remove it. Be sure to handle the broken part with work gloves and disconnect power to the appliance before changing the bulb.
Microwave Lamp Holder – Part Number: 6620G00007B
$21.45
In Stock
Microwave Lamp Holder
★★★★★
★★★★★
(2)
Part #6620G00007B
This genuine OEM light socket provides power to the light bulb in your microwave while holding it in place. This light socket is two pronged and the bulb should screw easily into it. If your light bulb will not light, check the bulb itself and light socket’s connection. If the socket is broken, or faulty it should be replaced immediately. Make sure to remove the high-voltage capacitor from your microwave before beginning this repair.
Rivet – Part Number: 4051W3A001A
$6.40
In Stock
Magnetron – Part Number: 6324W1A001L
$130.68
In Stock
Magnetron
★★★★★
★★★★★
(8)
Part #6324W1A001L
This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the microwave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.
Diaphragm-carburetor – Part Number: 270026
No Longer Available
Diaphragm-carburetor
★★★★★
★★★★★
(3)
Part #270026
This is a carburetor diaphragm, which is an OEM part that pumps fuel from the tank to the engine. It is roughly 1x2 inches and black in color. Sold individually, this part can fail due to fatigue and wear, and if it is broken you may notice your engine is running rough or not starting. If your engine exhibits these signs of being starved of fuel, your diaphragm is damaged and needs to be replaced. Our customers found this repair to be of medium difficulty. It requires a wrench, screwdriver, and pliers to complete. You will be able to locate your diaphragm inside the carburetor itself to swap it out with your new one.
Microwave Motor Ac Synchronous – Part Number: 6549W1S013H
$43.18
In Stock
Microwave Motor Ac Synchronous
★★★★★
★★★★★
(5)
Part #6549W1S013H
If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is making a grinding noise it will need to be replaced. If the motor does not turn, you can check for voltage or continuity with a multi-meter. Make sure the power is disconnected from your microwave before beginning this repair.
Microwave Screwtapping – Part Number: 1TTL0402818
$13.92
Special Order
High Voltage Diode – Part Number: 6021W3B001V
$17.15
In Stock
Switch,Micro – Part Number: 3B73361E
$21.45
Special Order
Switch,Micro
Part #3B73361E
This is a micro switch, but you may also know it as a door switch and it is compatible with your microwave. The function of the micro switch is to communicate to the electronic control board of your appliance when the door is opened and closed. If this part is broken and needs replacing you will notice your timer activated but the food inside is not being heated. This part measures to be roughly 1.5 inches long by just over half an inch wide, and it is black in color. You will find the location of this part behind the front panel of your microwave.

Exact Part matches for your search term

PANEL – Part Number: 8060
$43.93
Special Order
PANEL
This part number matches the current model number 8060
Part #8060
Lock Washer, 8-pack – Part Number: 8060
No Longer Available
Lock Washer, 8-pack
This part number matches the current model number 8060
Part #8060
FLANGE DCW – Part Number: 8060
$114.03
Special Order
FLANGE DCW
This part number matches the current model number 8060
Part #8060

Common Symptoms of models starting with 8060

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Could not keep an aftermarket muffler on the engine.
15 of 20 people found this instruction helpful.
  • Richard from KERNERSVILLE, NC
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Once I determined what OEM muffler I needed, installation was relatively easy. I have a 1982 4hp Briggs on my Snapper tiller. There was a 90* galvanized elbow coming out of the exhaust port, with a bezel nut to lock it down. Do not remove the elbow, even though it appears that you should. If you install the muffler without the elbow the m uffler will parallel the the vacuum for the carburetor and can melt the rubber couplers. Use the elbow to direct the heat away from the carburetor. Use a pipe wrench to lock down the bezel nut because the weight of the muffler, especially under vibration, can work loose and fall down on the tine belt cover and melt it. The bezel nut that comes with the muffler should also be used to lock down the muffler to the threaded intake bracket that comes with the muffler, not to replace the bezel nut for the elbow.
Was this helpful?
Thank you for voting!
One of the "night" lights burned out
7 of 8 people found this instruction helpful.
  • Ben from Chambersburg, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed one screw that held the bulb cover over the bulb. Removed the cover, removed the bulb, inserted new bulb, replaced cover, replaced the retaining screw.
Was this helpful?
Thank you for voting!
Magnitron failed
8 of 13 people found this instruction helpful.
  • Joseph from WILTON, NH
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover .
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.
Was this helpful?
Thank you for voting!