80512 (ABWESEU) LG Dryer - Parts

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visib...Read morele damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, whi...Read morech could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.

This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer i...Read mores if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove th...Read moree front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason yo...Read moreu would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are noticing marks left on your clothes, a broken lint screen guide could be to blame. The lint screen guide is approximately 13 inches wide on its...Read more straight edge. It is made of plastic and is sold individually. This is an OEM part, directly from the manufacturer.

This is a thermostat for various models of LG dryers. This thermostat specifically is the rear high limit thermostat, and it is designed as a safety device to shut off power to your dryer if the internal temperature gets too high. This thermostat comes with a mounting bracket, so you only need the securing screws to fully install it, alon...Read moreg with connecting the appropriate wire, after removing the old thermostat. If your dryer is no longer heating properly, or will not start, this thermostat may have been used and is no longer operational. Replacing this thermostat will require you to partly disassemble your dryer, as it is located on the heating element housing. This thermostat is a genuine OEM part and is sold individually.

This genuine OEM felt gasket provides a cushioned seal between the inner tub of your electric dryer and the rear panel. It prevents your clothes from getting snagged and helps in heat retention. You will find it around the circumference of the drum. The most typical reason for replacing the felt seal is when it becomes worn. It is importa...Read morent to note that this rear seal is sold separately from the front seal and the adhesive needed to install it.

Don't let your fresh fruits and veggies go to waste! The GE Crisper Drawer is here to help. Also known as a PAN ASM, this nifty drawer can expertly manage humidity levels, providing the ideal storage environment for your fruits and vegetables. That means they stay crunchy, ripe, and delicious for longer. But why is it so important? Simp...Read morele. It's the key to keeping your food at the highest quality for as long as possible. This function, specifically designed for refrigerators, is an essential part of maintaining top-notch food storage standards. Before you install the Crisper Drawer, take a quick peek at your refrigerator's owner's manual for step-by-step instructions?it's easier than you may think. Remember, this part is crafted by GE - a brand renowned for its commitment to exceptional performance. Trust us, your refrigerator (and your fresh produce) will thank you. So, let's get your fridge back to working like a champ with this indispensable Crisper Drawer!

This part is the replacement lint filter cover for your dryer. It is made of gray plastic and is approximately 11-1/2 inches by 1-1/4 inches. The lint filter cover fits on top of the lint filter and protects it. The main reason you would want to replace the lint filter cover is if it is cracked or broken. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.