797091 Briggs and Stratton Engine - Parts

Authentic Manufacturer Sourced replacement part used on a variety of Engines. This rocker cover gasket is for the cylinder head. It is sold Individually. It provides a strong seal to protect from leaks. Over time gaskets tend to deteriorate and would need to be replaced.

This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium. This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaf...Read moret, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and the seal allows combustion to occur, making your engine run at peak performance. If the gasket is damaged or coming apart, you may notice a ...Read moredecrease in the power and performance of your engine. When you remove the old gasket, be sure that the surface you are attaching the new one to is completely clean, so the seal will be effective. This part is sold individually and it is a genuine OEM part.

This is a genuine OEM sourced replacement exhaust gasket. It is specially made for use with Briggs and Stratton engines commonly used on Toro lawn and garden equipment. Its purpose is to provide an air-tight seal between the carburetor and the exhaust tube. Over time this gasket will deteriorate requiring replacement. Please note, this co...Read moremposite gasket is sold individually. To replace this part you will need a wrench.

This gear-governor is a special component that helps to engage the drive shaft. It is a genuine Briggs and Stratton item that is supplied by the original manufacturer for use with small engines that are commonly installed on a variety of lawn and garden equipment. It provides an identical replacement for a damaged or a missing hardware th...Read moreat was installed on a new unit. Check the diagrams for your model for the exact location and the correct installation of this part. One durable metal gear-governor is included. You may need a screwdriver and a wrench set to perform this repair.

It is an authentic part that is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this gasket is to provide a tight seal for the intake manifold, unfortunately, over time the material will wear out and may begin to fail eventually requir...Read moreing a replacement to maintain top performance. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable composite material and is sold individually.

This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.

This is a genuine OEM part. The Briggs & Stratton valve seal is used on many lawn tractor machines. The metal part stops oil from moving into the cylinder from the valve stem. This item is often fastened to the intake valve and the valve keeper. A screwdriver, socket set and wrench set are required for the installation. The metal valve seal is sold individually.

This engine ring set is a genuine OEM replacement designed for small engine applications. It helps seal the cylinder properly to maintain compression, reduce oil consumption, and restore smooth, efficient engine operation. Ideal for engine rebuilds or repairs, this ring set should be replaced when wear causes power loss, excessive oil use, or reduced overall performance.

This authentic item is supplied directly from the original equipment manufacturer for use with engines, outboard motors, portable generators, snowthrowers, and lawn mowers made by Briggs & Stratton and Toro. The o-ring seal attaches to the dipstick. When replacing this part a socket set might be required during the installation process. I...Read moret is made out of rubber and will need to be replaced if it breaks. This part is available as an individual replacement.

This is an OEM part sourced directly from the manufacturer. The governor shaft seal is designed for use in lawn tractors from Toro and engines from Briggs & Stratton. This part is made of high-quality plastic, and is used to help prevent leakage along the governor crank. You may require a wrench and pliers when replacing this part. This item is sold individually.