EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79692192900 Kenmore Dryer - Parts

1 - 12 of 94

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Lint Filter – Part Number: ADQ56656401
$36.85
In Stock
Dryer Lint Filter
★★★★★
★★★★★
(178)
Part #ADQ56656401
This dryer lint filter assembly captures lint, hair, and loose fabric fibres as air leaves the drum. Its fine mesh screen allows air to pass through while collecting debris for easy removal after each load. A torn screen, cracked frame, or warped edge may let lint bypass the filter or prevent it from seating properly. Replacing a damaged assembly restores the screening surface and secure support. Cleaning collected lint after every load helps maintain airflow and supports normal drying times during everyday use. This is an OEM part sourced directly from the manufacturer.
4 PACK ROLLER ASSEMBLY – Part Number: 4581EL2002L
$144.76
In Stock
4 PACK ROLLER ASSEMBLY
★★★★★
★★★★★
(82)
Part #4581EL2002L
This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, which could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.
Lint Screen Housing – Part Number: MCK49049101
$48.35
In Stock
Lint Screen Housing
★★★★★
★★★★★
(23)
Part #MCK49049101
Clothing stays separated from the lint duct opening with help from this gray plastic dryer lint filter cover and guide. It supports the removable lint screen and provides a smooth barrier around the filter area as laundry tumbles. Cracks, broken edges, or warping may cause garments to snag or prevent the screen from seating securely. Replacing a damaged cover helps restore filter support and protects the opening around the lint duct. The guide also supports routine removal and insertion of the screen for cleaning. This is an OEM part sourced directly from the manufacturer.
Moisture Sensor – Part Number: 6500EL3001A
$21.95
In Stock
Moisture Sensor
★★★★★
★★★★★
(6)
Part #6500EL3001A
Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clothes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
Dryer Drum Belt – Part Number: 4400EL2001F
$37.35
In Stock
Dryer Drum Belt
★★★★★
★★★★★
(8)
Part #4400EL2001F
Get clothes tumbling again with this dryer drum drive belt. It wraps around the drum and runs over the motor and tension pulleys, transferring motor power to turn the drum during drying. A cracked, stretched, or broken belt may slip, make unusual noises, or leave the drum still while the motor runs. Replacing a worn belt helps restore steady tumbling so clothes move through the warm air. Unplug the dryer before opening the cabinet, and follow the installation directions for proper belt routing. This is an OEM part sourced directly from the manufacturer.
Blower Thermostat – Part Number: 6931EL3002M
$53.85
In Stock
Blower Thermostat
★★★★★
★★★★★
(8)
Part #6931EL3002M
Monitor exhaust air temperature with this dryer blower housing thermostat. Mounted on the blower assembly, it responds to heat and opens its electrical circuit when the temperature reaches its set limit, helping protect the dryer from overheating. A failed thermostat may interrupt operation, leaving the dryer unable to start or heat properly. Replacing a faulty thermostat helps restore the temperature safety circuit. Unplug the dryer before opening the cabinet, and clear lint from the exhaust path to support proper airflow. This is an OEM part sourced directly from the manufacturer.
High Limit Thermostat and Thermistor Kit – Part Number: AGM30045804
$103.35
In Stock
High Limit Thermostat and Thermistor Kit
★★★★★
★★★★★
(14)
Part #AGM30045804
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.
Filter Guide – Part Number: MEA49050001
$33.83
In Stock
Filter Guide
★★★★★
★★★★★
(7)
Part #MEA49050001
A securely seated lint screen depends on an intact guide inside the dryer filter opening. This plastic lint filter frame supports the removable screen and guides it into place during insertion. Cracks, warping, or broken edges may leave the filter loose, prevent it from seating fully, or make removal difficult. Replacing a damaged guide helps restore proper filter support and limits gaps that allow lint to pass around the screen. The frame also keeps the filter aligned for routine removal and cleaning. This is an OEM part sourced directly from the manufacturer.
Gas Igniter – Part Number: 5318EL3001A
$134.43
In Stock
Gas Igniter
★★★★★
★★★★★
(3)
Part #5318EL3001A
Gas burner ignition begins when this dryer igniter heats to a glowing temperature, allowing the burner to light and produce drying heat. The assembly includes a mounting bracket and wire harness for connection to the ignition circuit. A cracked or burned out igniter may prevent a flame from forming, leaving the drum tumbling without heat and clothes damp. Replacing a faulty assembly helps restore burner ignition and normal heating. The fragile heating surface requires careful handling to avoid damage during installation. This is an OEM part sourced directly from the manufacturer.
Felt Seal – Part Number: 4036EL3001A
$52.75
In Stock
Felt Seal
★★★★★
★★★★★
(4)
Part #4036EL3001A
Warm air stays within the intended drying path with help from this dryer drum felt seal. It closes the gap between the rotating drum and stationary housing while providing a cushioned contact surface as the drum turns. A worn, torn, or displaced seal may allow air and lint to escape into the cabinet or cause scraping noises during operation. Replacing a damaged seal helps restore proper airflow through the drum and reduces rubbing at the sealed edge, supporting smoother rotation and normal drying performance. This is an OEM part sourced directly from the manufacturer.
Safety Switch Assembly – Part Number: EBF61496102
$52.75
In Stock
Pulley Idle – Part Number: 4560EL3001A
$30.53
In Stock
Pulley Idle
★★★★★
★★★★★
(5)
Part #4560EL3001A
The drive belt moves smoothly around this dryer idler pulley wheel as the motor turns the drum. Working within the belt tensioning mechanism, the pulley guides the belt and helps maintain steady contact with the drive system. A worn, cracked, or seized wheel may cause squealing, grinding, belt slippage, or interrupted tumbling. Replacing a damaged pulley helps restore free belt movement and reliable drum rotation. Its rotating surface supports the belt during operation, reducing the friction that can lead to noise and premature belt wear. This is an OEM part sourced directly from the manufacturer.
1 - 12 of 94