EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79691379210 Kenmore Dryer - Parts

1 - 12 of 104

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
4 PACK ROLLER ASSEMBLY – Part Number: 4581EL2002L
$144.76
In Stock
4 PACK ROLLER ASSEMBLY
★★★★★
★★★★★
(82)
Part #4581EL2002L
This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, which could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.
Dryer Lint Filter – Part Number: 5231EL1003B
$49.95
In Stock
Dryer Lint Filter
★★★★★
★★★★★
(73)
Part #5231EL1003B
This lint filter fits select clothes dryers. It catches lint, dust, and clothing fibers before they enter the dryers air system. A clean filter helps maintain good airflow and drying performance. Replace it if the screen is torn, cracked, bent, or has holes. Clean the filter after every load and remove any buildup with a soft brush when needed. Use the complete dryer model number to guarantee the proper fit. No tools are normally needed because the filter slides into the opening near the dryer door. This is an OEM part sourced directly from the manufacturer.
Moisture Sensor – Part Number: 6500EL3001A
$21.95
In Stock
Moisture Sensor
★★★★★
★★★★★
(6)
Part #6500EL3001A
Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clothes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
Dryer Drum Belt – Part Number: 4400EL2001F
$37.35
In Stock
Dryer Drum Belt
★★★★★
★★★★★
(8)
Part #4400EL2001F
Get clothes tumbling again with this dryer drum drive belt. It wraps around the drum and runs over the motor and tension pulleys, transferring motor power to turn the drum during drying. A cracked, stretched, or broken belt may slip, make unusual noises, or leave the drum still while the motor runs. Replacing a worn belt helps restore steady tumbling so clothes move through the warm air. Unplug the dryer before opening the cabinet, and follow the installation directions for proper belt routing. This is an OEM part sourced directly from the manufacturer.
Blower Thermostat – Part Number: 6931EL3002M
$53.85
In Stock
Blower Thermostat
★★★★★
★★★★★
(8)
Part #6931EL3002M
Monitor exhaust air temperature with this dryer blower housing thermostat. Mounted on the blower assembly, it responds to heat and opens its electrical circuit when the temperature reaches its set limit, helping protect the dryer from overheating. A failed thermostat may interrupt operation, leaving the dryer unable to start or heat properly. Replacing a faulty thermostat helps restore the temperature safety circuit. Unplug the dryer before opening the cabinet, and clear lint from the exhaust path to support proper airflow. This is an OEM part sourced directly from the manufacturer.
High Limit Thermostat and Thermistor Kit – Part Number: AGM30045804
$103.35
In Stock
High Limit Thermostat and Thermistor Kit
★★★★★
★★★★★
(14)
Part #AGM30045804
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.
Lint Filter Guide Cover – Part Number: 3550EL1006B
$57.15
In Stock
Lint Filter Guide Cover
★★★★★
★★★★★
(21)
Part #3550EL1006B
Clothing stays separated from the lint duct opening with help from this gray plastic dryer lint filter cover and guide. It supports the lint screen and guides it into place for regular removal and cleaning. Cracks, broken edges, or a warped guide may cause garments to snag near the lint trap or make the filter difficult to insert and remove. Replacing a damaged cover restores a smooth barrier around the opening and helps keep the lint screen securely seated during dryer operation. This is an OEM part sourced directly from the manufacturer.
Gas Igniter – Part Number: 5318EL3001A
$134.43
In Stock
Gas Igniter
★★★★★
★★★★★
(3)
Part #5318EL3001A
Gas burner ignition begins when this dryer igniter heats to a glowing temperature, allowing the burner to light and produce drying heat. The assembly includes a mounting bracket and wire harness for connection to the ignition circuit. A cracked or burned out igniter may prevent a flame from forming, leaving the drum tumbling without heat and clothes damp. Replacing a faulty assembly helps restore burner ignition and normal heating. The fragile heating surface requires careful handling to avoid damage during installation. This is an OEM part sourced directly from the manufacturer.
PARTS ASSEMBLY – Part Number: 383EEL3002R
$19.40
In Stock
PARTS ASSEMBLY
★★★★★
★★★★★
(3)
Part #383EEL3002R
This genuine OEM conversion kit allows your dryer to be converted from using natural gas to liquid propane. It caters to homes that rely on propane for their energy needs. This kit comes with an orifice that controls the flow rate of propane gas, and replaces the one originally installed on the gas burner in your dryer. This kit is sold individually. Proceed with caution when installing it yourself to ensure safe and proper installation.
Felt Seal – Part Number: 4036EL3001A
$52.75
In Stock
Felt Seal
★★★★★
★★★★★
(4)
Part #4036EL3001A
Warm air stays within the intended drying path with help from this dryer drum felt seal. It closes the gap between the rotating drum and stationary housing while providing a cushioned contact surface as the drum turns. A worn, torn, or displaced seal may allow air and lint to escape into the cabinet or cause scraping noises during operation. Replacing a damaged seal helps restore proper airflow through the drum and reduces rubbing at the sealed edge, supporting smoother rotation and normal drying performance. This is an OEM part sourced directly from the manufacturer.
Safety Switch Assembly – Part Number: EBF61496102
$52.75
In Stock
Filter Guide – Part Number: 4974EL1002B
$52.75
In Stock
Filter Guide
★★★★★
★★★★★
(1)
Part #4974EL1002B
This filter guide fits select clothes dryers. It supports the lint filter and helps keep it lined up with the air duct. It also keeps clothing away from the lint filter opening during the drying cycle. Replace the guide if it is cracked, bent, or causing clothes to snag. The flap and spring may be sold separately. Use the complete dryer model number to guarantee the proper fit. Unplug the dryer and wear work gloves before starting the repair. This is an OEM part sourced directly from the manufacturer.
1 - 12 of 104