79691372210 Kenmore Dryer - Parts

This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, whi...Read morech could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.

The lint filter in your dryer is used to collect lint as it passes through the dryer vent. If you notice that your dryer is not providing enough heat, or if it takes too long to dry, you may need to replace the lint filter. You should also replace the lint filter if you notice it is damaged during regular maintenance. Many of our customer...Read mores have rated this repair as easy. To complete the repair, simply remove the old lint filter and replace it with the new one. You may want to use a flat head screwdriver to remove any residual lint before you install the new filter.

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove th...Read moree front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason yo...Read moreu would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

Located just inside the dryer door. The guide cover (or grill cover) is where the hot air circulates through the appliance. This part may crack or become damaged over time, causing clothes to get caught on it while it is in motion. Open the dryer door, remove the lint screen, and remove the screen using your screwdriver. Line up the new g...Read morerill cover with the moisture sensor and the housing on either side, and it should snap into place. Once it is firmly in place, use your screwdriver to put the screws back in.

This spiral-style gas burner igniter is designed for use in select gas dryers and plays a crucial role in generating the heat needed to dry clothes. Operating at 120 volts, the igniter glows red hot during the drying cycle to ignite the gas that heats the drum. If your dryer runs but fails to produce heat, the igniter may be faulty and sh...Read moreould be replaced. The assembly includes the igniter, bracket, wire harness, and plug for straightforward installation. Always disconnect the dryer from power before beginning any repairs to ensure safety.

This genuine OEM conversion kit allows your dryer to be converted from using natural gas to liquid propane. It caters to homes that rely on propane for their energy needs. This kit comes with an orifice that controls the flow rate of propane gas, and replaces the one originally installed on the gas burner in your dryer. This kit is sold i...Read morendividually. Proceed with caution when installing it yourself to ensure safe and proper installation.

This genuine OEM felt gasket provides a cushioned seal between the inner tub of your electric dryer and the rear panel. It prevents your clothes from getting snagged and helps in heat retention. You will find it around the circumference of the drum. The most typical reason for replacing the felt seal is when it becomes worn. It is importa...Read morent to note that this rear seal is sold separately from the front seal and the adhesive needed to install it.

Don't let your fresh fruits and veggies go to waste! The GE Crisper Drawer is here to help. Also known as a PAN ASM, this nifty drawer can expertly manage humidity levels, providing the ideal storage environment for your fruits and vegetables. That means they stay crunchy, ripe, and delicious for longer. But why is it so important? Simp...Read morele. It's the key to keeping your food at the highest quality for as long as possible. This function, specifically designed for refrigerators, is an essential part of maintaining top-notch food storage standards. Before you install the Crisper Drawer, take a quick peek at your refrigerator's owner's manual for step-by-step instructions?it's easier than you may think. Remember, this part is crafted by GE - a brand renowned for its commitment to exceptional performance. Trust us, your refrigerator (and your fresh produce) will thank you. So, let's get your fridge back to working like a champ with this indispensable Crisper Drawer!

This genuine OEM filter guide keeps garments from exhaust air duct and lint screen inside the dryer. The filter guide is made of high quality plastic and is approximately 15 inches long by 3 inches wide. If your filter guide is faulty, or damaged clothes can get stuck in the lint screen which can cause damage to your garments and to the d...Read moreryer unit itself. NOTE: Flap (PS3634953) and Spring (PS11706080) are sold separately.