EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

79681472210 Kenmore Dryer - Parts

1 - 12 of 48

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
4 PACK ROLLER ASSEMBLY – Part Number: 4581EL2002L
$144.76
In Stock
4 PACK ROLLER ASSEMBLY
★★★★★
★★★★★
(82)
Part #4581EL2002L
This part is sold individually. The drum support roller is found in your dryer. It is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. It is recommended that you replace both rollers at once. You may notice that this part needs to be replaced if you are experiencing a squeaking noise, which could be due to the bearing going bad. The bearing could be severely damaged if you hear a very loud thumping noise, much like you would when you are drying a pair of shoes.
Thermal Fuse – Part Number: 6931EL3003D
$19.75
In Stock
Thermal Fuse
★★★★★
★★★★★
(28)
Part #6931EL3003D
This thermal fuse acts as a high-limit thermostat, and shuts off the heating element when the dryer overheats by cutting off power to the dryer. If the thermal fuse has blown, the dryer will not start. These fuses cannot be reset, so if yours has blown, you will need to replace it. A common reason for the thermal fuse to blow on a dryer is if the exhaust vent on your dryer is restricted or blocked. Hot air will be confined in the dryer and the fuse will trip and stop the electricity from flowing to the gas valve or heating element.
Moisture Sensor – Part Number: 6500EL3001A
$21.95
In Stock
Moisture Sensor
★★★★★
★★★★★
(6)
Part #6500EL3001A
Damp clothing makes contact with this dryer moisture sensor bar as it tumbles, providing an electrical signal used to monitor drying progress. The metal electrode works with the control system to adjust automatic cycle time as the load becomes drier. A damaged bar or poor electrical contact may cause the cycle to end too soon or leave clothes damp. Replacing a faulty sensor bar helps restore moisture detection, allowing the dryer controls to respond to the load and finish at the selected dryness level. This is an OEM part sourced directly from the manufacturer.
Dryer Drum Belt – Part Number: 4400EL2001F
$37.35
In Stock
Dryer Drum Belt
★★★★★
★★★★★
(8)
Part #4400EL2001F
Get clothes tumbling again with this dryer drum drive belt. It wraps around the drum and runs over the motor and tension pulleys, transferring motor power to turn the drum during drying. A cracked, stretched, or broken belt may slip, make unusual noises, or leave the drum still while the motor runs. Replacing a worn belt helps restore steady tumbling so clothes move through the warm air. Unplug the dryer before opening the cabinet, and follow the installation directions for proper belt routing. This is an OEM part sourced directly from the manufacturer.
Blower Thermostat – Part Number: 6931EL3002M
$53.85
In Stock
Blower Thermostat
★★★★★
★★★★★
(8)
Part #6931EL3002M
Monitor exhaust air temperature with this dryer blower housing thermostat. Mounted on the blower assembly, it responds to heat and opens its electrical circuit when the temperature reaches its set limit, helping protect the dryer from overheating. A failed thermostat may interrupt operation, leaving the dryer unable to start or heat properly. Replacing a faulty thermostat helps restore the temperature safety circuit. Unplug the dryer before opening the cabinet, and clear lint from the exhaust path to support proper airflow. This is an OEM part sourced directly from the manufacturer.
High Limit Thermostat and Thermistor Kit – Part Number: AGM30045804
$103.35
In Stock
High Limit Thermostat and Thermistor Kit
★★★★★
★★★★★
(14)
Part #AGM30045804
This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shortening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.
Filter Guide – Part Number: MEA49050001
$33.83
In Stock
Filter Guide
★★★★★
★★★★★
(7)
Part #MEA49050001
A securely seated lint screen depends on an intact guide inside the dryer filter opening. This plastic lint filter frame supports the removable screen and guides it into place during insertion. Cracks, warping, or broken edges may leave the filter loose, prevent it from seating fully, or make removal difficult. Replacing a damaged guide helps restore proper filter support and limits gaps that allow lint to pass around the screen. The frame also keeps the filter aligned for routine removal and cleaning. This is an OEM part sourced directly from the manufacturer.
Dryer Thermostat Assembly – Part Number: 6931EL3001F
$58.25
In Stock
Dryer Thermostat Assembly
★★★★★
★★★★★
(2)
Part #6931EL3001F
Temperature protection in the dryer heating system depends on this rear high-limit thermostat assembly. It senses heat at its mounting location and opens the heating circuit when the temperature reaches its cutoff point, helping prevent excessive heat from damaging surrounding components. A faulty thermostat may interrupt heating, leave clothes damp, or prevent normal temperature control. Replacing a failed assembly helps restore the protective switching function needed during drying. The thermostat works within the heating circuit to limit heat when operating temperatures rise too high. This is an OEM part sourced directly from the manufacturer.
Felt Seal – Part Number: 4036EL3001A
$52.75
In Stock
Felt Seal
★★★★★
★★★★★
(4)
Part #4036EL3001A
Warm air stays within the intended drying path with help from this dryer drum felt seal. It closes the gap between the rotating drum and stationary housing while providing a cushioned contact surface as the drum turns. A worn, torn, or displaced seal may allow air and lint to escape into the cabinet or cause scraping noises during operation. Replacing a damaged seal helps restore proper airflow through the drum and reduces rubbing at the sealed edge, supporting smoother rotation and normal drying performance. This is an OEM part sourced directly from the manufacturer.
Safety Switch Assembly – Part Number: EBF61496102
$52.75
In Stock
Filter Cover – Part Number: MCK66787901
$48.35
In Stock
Filter Cover
Part #MCK66787901
This dryer lint filter screen cover helps keep clothing and small items from slipping into the exhaust duct near the lint filter. The plastic flap fits into the filter housing and covers the opening when the lint screen is removed. Cracks, warping, or broken mounting tabs may keep the cover from sitting properly or moving as it should. Replacing a damaged or missing cover restores this protective barrier and helps prevent clothing from catching on broken edges around the lint filter area. This is an OEM part sourced directly from the manufacturer.
Pulley Idle – Part Number: 4560EL3001A
$30.53
In Stock
Pulley Idle
★★★★★
★★★★★
(5)
Part #4560EL3001A
The drive belt moves smoothly around this dryer idler pulley wheel as the motor turns the drum. Working within the belt tensioning mechanism, the pulley guides the belt and helps maintain steady contact with the drive system. A worn, cracked, or seized wheel may cause squealing, grinding, belt slippage, or interrupted tumbling. Replacing a damaged pulley helps restore free belt movement and reliable drum rotation. Its rotating surface supports the belt during operation, reducing the friction that can lead to noise and premature belt wear. This is an OEM part sourced directly from the manufacturer.
1 - 12 of 48