This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
This is a replacement sensor assembly for your washer. It may also be known as a motor rotor position sensor. The sensor assembly monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer pumps but will not spin or agitate, you may have a damaged sensor assembl...Read morey. This part is sold individually, and is an OEM part sourced directly from the manufacturer. Be sure to shut off the power to your washer before you begin this repair.
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
This drain pump assembly is a genuine replacement part designed for select LG and Kenmore washing machines. It plays a critical role in removing water from the washer tub during the drain cycle, ensuring efficient water evacuation and proper cycle completion. Powered by an 85-watt, 120-volt motor, the pump is typically located near the dr...Read moreain hose at the bottom of the appliance. A failing pump may result in water remaining in the tub, incomplete draining, or unusual grinding or knocking noises during operation. Replacing the pump restores proper drainage and helps prevent water damage or cycle interruptions. Installation should be performed with the washer unplugged and may require basic tools and moderate repair experience.
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plastic and comes with two clamps to secure it within your washer, one on each end. If you notice your washer is leaking check to make sure if t...Read morehis hose is cracked or damaged, because it will need to be replaced immediately. This drain hose is an OEM part that is sold individually and will require you to disassemble part of your washer to replace it.
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive system between the appliance spin and agitate cycles. Is measures 14.5 inches in diameter. You may need to replace this part if you hear strange noises or if the washer will not spin or agitate.
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pump, and it is responsible for transporting water out of the washing machine after a cycle. If the drain hose is kinked, damaged, or clogged, ...Read morethe washer will leak, or you may find standing water in the drum at the end of the cycle. Each drain hose comes with a metal clamp for fastening.
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It ensures that the washer uses the appropriate amount of water for each cycle and load type. This genuine OEM assembly includes not only the switch itself but also the accompanying air dome tube.
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The lid switch holds lets your washer know when the door is latched, so it can begin the wash cycle. If the lid switch is damaged, it will not all...Read moreow the washer to run properly. Be sure to disconnect the washer from the power and water sources before you begin this repair. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pastor - For model number 79631512211
April 26, 2023
Washing machine overflows when filling. Is ther an orifice that regulates the volume of water?
Hi Pastor, thank you for reaching out. Based on our research, you may need to check the pressure switch assembly, part number PS3529177, as it identifies how much water is in the machine and tells the control board if the machine has been filled or emptied. We hope this helps, good luck with the repair!
Once the tub fills and it starts the washing action we hear a louder than normal grinding noise. Similar to what it always done much louder.
Thanks.
Hi William, thank you for the question. We believe your washing machine is having this problem because of the faulty clutch housing assembly. We recommend you replace the clutch housing assembly, part number PS11708484, to fix the issue. We hope this solves your problem!
Hello Vincent, thank you for your inquiry. Based on our research, an off-balance washer may cause a leak from the top during the spin cycle. We would recommend checking the suspension rod, part number PS3635695, to fix the issue. It supports the washer tub and keeps it stable. We hope this solves your problem!
My washer won’t fill with water. I have checked the supply lines, the water inlet valve for continuity, changed the pressure switch. Still nothing! Help!
Hello Melissa, thank you for your question. We would recommend checking the water inlet tubing and making sure no tube is blocked or kinked. If the water pressure is not less than 20 psi and the problem persists, we would recommend replacing the water inlet valve, part number PS12374721. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Hello Stephen, thank you for reaching out. Remove the entire drawer assembly and clean the top of the dispenser housing with a bristled brush, then clean the drawer and all components with hot water. This should take care of it. Then remove the hoses from the rear of the dispenser and be sure they are clear of all mineral deposits and clean as well. Make sure to clean them if they have a restricted flow. If this does not help, you need to replace the bleach dispenser, part number PS3627301. Please reach out to customer service if you need help placing an order. Glad to be of help!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
LE Error Message and won't spin drum properly
255 of 339 peoplefound this instruction helpful.
Mark from Harrisburg, PA
Easy
30 - 60 mins
Screw drivers, Socket set
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the
... Read more motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
Read less
Was this helpful?
Thank you for voting!
LE fail code
30 of 32 peoplefound this instruction helpful.
scott from GODDARD, KS
Really Easy
30 - 60 mins
Screw drivers, Socket set
Removed back of washer with screw driver, Removed outer motor cover with a 17 mm socket (1 bolt), Removed motor stater using 10 mm socket (8 bolts). Left motor plugged in and and tipped to the side exposing the sensor. Unplug and snap off sensor. Reassembled in opposite order. Machine works great. Very easy fix, and perfect fit on part.
Was this helpful?
Thank you for voting!
It did not drain water, cycle stops at rinse+spin.
28 of 36 peoplefound this instruction helpful.
Jesus from El Paso, TX
Very Easy
15 - 30 mins
Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read morepplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
My Orders
