Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Remove and replace light switch
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.
removed the upper freezer door to access screws to remove lower door. laid bottom door on its side, removed bad bushing, put new bushing in, put bottom door back on refridge, put upper door back on fridge. Door worked easy as when new. good closure of door and story..Happy customer, and wife even happier.....thank you....
Both cams had broken off the gasket retainer strips
Check YouTube, but no one shows all the details. Need to swap hinges and spring from old retainer to new retainers by removing screw at bottom of hinge, then removing rod with small screwdriver to poke the rod out. I laid the old and new side by side and did swap to ensure proper orientation. Attach cams before sliding gasket retainer back into gasket, I used a few drops of liquid soap as lubricant on the retainer to help it slide in. Very important to ensure the edge of the retainer is tucked behind the door edge or else things will not fit correctly. I did it a few times before I got it right, but didn’t break anything else. Good luck.
bottom door dropped slightly and bottom hinge area rubbing on steel door support
removed 3 fasteners for top door and placed freezer door aside, then removed 3 more fasteners on bottom refrigerator door and place that aside. replaced bushing on lower door bracket and reversed the above procedure to reinstall doors.
Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping. Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minutes.
Unplugged the refrigerator. Used small flat head screw driver to push the front tab of the old switch in and pulled it out with pliers. Detached and reattached the wires to the switch. Reinserted back into hole. Plugged refrigerator back in to power. All good.
Refrigerator light not working. If I would flick the button it would go on for a minute but not stay on.
The old switch was a little hard to get out....took me a couple tries. I couldn’t move the frig out to unplug it, so just shut the power off in the kitchen. But, I was happy that’s what the problem was and so happy to have the light back on......it was probably three years it didn’t work!
After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it popped out, you may need to use pliers to disconnect the switch.
Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.
Ordered part from part select. Received part with out instructions. It took only one screwdriver for 1 screw removal and then removing cover to replace switch. Pretty simple
Very simple Removed wire rack Removed 3 phillips head screws, requires large phillips screw driver Removed old rail guide Installed new rail guide and screwed back in place Reinstalled rack