7957803 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The ice maker in freezer P/NO 5988JA0002Y would leak water and make giant ice block
5 of 8 people
found this instruction helpful.
-
Eric from SURPRISE, AZ
- Really Easy
- 30 - 60 mins
I ordered and replaced the ice maker. To replace:
1. Go behind refrigerator and unplug electrical cord and turn off water supply.
2. In freezer locate electrical plug for ice maker. It has two tabs on the left and right side of it. Lift the tabs and pull the plug to disconnect it.
3. Remove the three screw ... Read more s, 2 on top and 1 on bottom of ice maker You can actually leave the screws in place if you loosen them sufficiently and lift the ice maker off of the screws and washers.
4. Install the new ice maker using the screws and plastic washers to secure it.
5. Plug the electrical connector for ice maker into the receptacle. Note: The plug only goes one way and is keyed with different shaped plugs and holes. The wires on my plug naturally fell upside down so I had to turn the plug 180 degrees to make it fit in the slot.
6. Turn on water and check for leaks.
7. Plug back in refrigerator and you should have ice in less than 12 hours.
1. Go behind refrigerator and unplug electrical cord and turn off water supply.
2. In freezer locate electrical plug for ice maker. It has two tabs on the left and right side of it. Lift the tabs and pull the plug to disconnect it.
3. Remove the three screw ... Read more s, 2 on top and 1 on bottom of ice maker You can actually leave the screws in place if you loosen them sufficiently and lift the ice maker off of the screws and washers.
4. Install the new ice maker using the screws and plastic washers to secure it.
5. Plug the electrical connector for ice maker into the receptacle. Note: The plug only goes one way and is keyed with different shaped plugs and holes. The wires on my plug naturally fell upside down so I had to turn the plug 180 degrees to make it fit in the slot.
6. Turn on water and check for leaks.
7. Plug back in refrigerator and you should have ice in less than 12 hours.
Read less
Was this helpful?
Thank you for voting!
Light doesn’t come on when fridge door opens
4 of 6 people
found this instruction helpful.
-
Lloyd G from QUEENS VLG, NY
- Really Easy
- 15 - 30 mins
Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.
Was this helpful?
Thank you for voting!
interior light switch did not turn off light in ref
4 of 6 people
found this instruction helpful.
-
Timothy from SUSANVILLE, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
pried out old switch, disconnected wires ,placed wires on new switch
Was this helpful?
Thank you for voting!
Door switch would not turn on interior refrigerator light.
3 of 4 people
found this instruction helpful.
-
Jane from SHORELINE, WA
- Very Easy
- Less than 15 mins
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new sw
... Read more
itch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Read less
Was this helpful?
Thank you for voting!
Ice maker not working but making a sound when turned on (buzzing). Water valve not functioning when tested with a multitester (multimeter).
3 of 4 people
found this instruction helpful.
-
shirley from FLORISSANT, MO
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Wrench set
I removed the old water valve, disconnected the water tube going in and tube going out to the back of the refrigerator. New water valve bracket different than the previous one which resulted in my having to modify it to fit. Not an easy task as it was preformed metal. Once hooked up, water turned on, and ice maker turned on, the sound
... Read more
I'm getting now is clunking and not making ice. My debate is whether or not to purchase a new ice maker or revert to the tried and true method with ice trays which work every time.
Read less
Was this helpful?
Thank you for voting!
Came without screws
2 of 2 people
found this instruction helpful.
-
PATRICIA from FORT MOHAVE, AZ
- Very Difficult
- More than 2 hours
-
Socket set
Screws into handle with tool once I located the screws which took most the day...
Disappointed with your employee for not acknowledging that screws were required and needed to be added to order...
Disappointed with your employee for not acknowledging that screws were required and needed to be added to order...
Was this helpful?
Thank you for voting!
Door was hanging up would close about half way
2 of 2 people
found this instruction helpful.
-
Kyong from Cusseta, GA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
Replaced hinges and bushing
Other Parts Used:
Was this helpful?
Thank you for voting!
light didn't come on when the door was opened
2 of 2 people
found this instruction helpful.
-
William L from SUMAS, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
The new part fit in quite easily.
Was this helpful?
Thank you for voting!
Switch stops working
2 of 2 people
found this instruction helpful.
-
David from PENNSVILLE, NJ
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Was this helpful?
Thank you for voting!
Freeze not sealing properly
2 of 2 people
found this instruction helpful.
-
mike from DAVIDSONVILLE, MD
- Easy
- 15 - 30 mins
Took off the door stop and put on the new one. Installed the new gasket and had another beer!!
Other Parts Used:
Was this helpful?
Thank you for voting!
Light switch for refrigerator not functioning
2 of 3 people
found this instruction helpful.
-
shirley from ONALASKA, WI
- Easy
- 30 - 60 mins
-
Screw drivers
Followed instructions online
Was this helpful?
Thank you for voting!
bad switch
1 person
found this instruction helpful.
-
Michael from TONAWANDA, NY
- Easy
- 15 - 30 mins
-
Screw drivers
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this helpful?
Thank you for voting!
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1 person
found this instruction helpful.
-
JON from OJAI, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs o
... Read more
n the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Read less
Was this helpful?
Thank you for voting!
Light quit coming on when door opened.
1 person
found this instruction helpful.
-
Calvin from Northome, MN
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this helpful?
Thank you for voting!
Not making ice but could hear the solenoid trying to work
1 person
found this instruction helpful.
-
Jesse from Pella, IA
- Very Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.
Was this helpful?
Thank you for voting!