Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I had broken the glass shelf which covered the fruit and vegetable drawers.he replacement was perfect fit.
2 of 2 peoplefound this instruction helpful.
CAROLE from COMPTCHE, CA
Very Easy
Less than 15 mins
I merely placed the new shelf in. Nothing to it. No tools needed. The replacement glass was a perfect fit.
Was this helpful?
Thank you for voting!
Plastic runner had broken
2 of 2 peoplefound this instruction helpful.
Genevieve from MADERA, CA
Very Easy
Less than 15 mins
Screw drivers
removed 2 screws and replaced them on new part. Very easy.
Was this helpful?
Thank you for voting!
The part did not fit
2 of 2 peoplefound this instruction helpful.
Stacy from ST AUGUSTINE, FL
Really Easy
30 - 60 mins
Like the customer who put a review on your site before me, I was unable to complete the repair because the inlet tube did not fit my refrigerator. I was hoping to speak to someone regarding this issue.
After noting frost in freezer Right rail started to jam. Noted freezer door was closing crooked. Rail replacement resolved issue. It had been frosting up for some time so Rail must have been broken for a while. Check door seals they were not closing flush.
Was this helpful?
Thank you for voting!
ice maker stopped working
3 of 5 peoplefound this instruction helpful.
SUREN from SAN RAMON, CA
Easy
30 - 60 mins
Screw drivers
replaced the ice maker with the new assembly kit, the longest time taken was to fit back the pull out door .. had to align the slots correctly and check that it slid back and forth easily.
Was this helpful?
Thank you for voting!
Broke right freezer rail
2 of 2 peoplefound this instruction helpful.
Richard from HOLLYWOOD, FL
Really Easy
15 - 30 mins
Screw drivers
Removed old rail by unscrewing 3 screws and put new rail on
Was this helpful?
Thank you for voting!
The light would not turn on (had the problem for years!) and the seal around the door was not very good.
2 of 2 peoplefound this instruction helpful.
Penelope from WEST CHESTER, OH
Really Easy
15 - 30 mins
Pliers, Screw drivers
1. Pull out the old gasket & push in the new one!
2. Pop out the light assembly with a screwdriver, disconnect the wire bracket, (the hardest part so I used pliers to grip the plastic) and connect the new one...pay attention to the direction to put it back in the space and you’re done! IF I CAN DO IT, YOU CAN DO IT! (Also check
... Read more you tube videos for accurate instructions & correct terminology!!!)
Went on line to see how difficult it would be to replace the valve. Through Google there was a video which showed in exact detail how to remove and replace the valve. Then went on line to find the replacement part which was readily available. The only problem was that the connection on the valve where the fill water enters the valve was l
... Read morearger than the old valve. To fix that I went to a local Ace hardware store and found a nut that would fit the valve connection. Also don't forget to use a compression ring to keep the fill line secured when replaced. Over all it was very simple and was in my "pay grade"
Read less
Was this helpful?
Thank you for voting!
Light quit coming on when door opened.
1 personfound this instruction helpful.
Calvin from Northome, MN
A Bit Difficult
15 - 30 mins
Screw drivers
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Was this helpful?
Thank you for voting!
Not making ice but could hear the solenoid trying to work
1 personfound this instruction helpful.
Jesse from Pella, IA
Very Easy
15 - 30 mins
Screw drivers, Wrench (Adjustable)
I turned off the water supply. Took off the access panel at the bottom of the fridge. Disconnected the waterlines from the valve. Remove the screw hole in the valve in place install the waterlines on the new valve attach the new valve to the refrigerator, reinstalled the back panel turn on the water And it made ice.
Was this helpful?
Thank you for voting!
The right hand glide for the top freezer drawer was broken.
1 personfound this instruction helpful.
Cathrine from NEW ORLEANS, LA
Very Easy
15 - 30 mins
Replaced the glide.
Was this helpful?
Thank you for voting!
INTERIOR DOOR ACTIVATED LIGHT SWITCH QUIT WORKING
1 personfound this instruction helpful.
JON from OJAI, CA
Really Easy
15 - 30 mins
Screw drivers
1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs o
... Read moren the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!
Read less
Was this helpful?
Thank you for voting!
bad switch
1 personfound this instruction helpful.
Michael from TONAWANDA, NY
Easy
15 - 30 mins
Screw drivers
The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.
Was this helpful?
Thank you for voting!
Lights didn't come on when door was opened
1 personfound this instruction helpful.
Philip from Ashland, MA
A Bit Difficult
15 - 30 mins
Pliers, Screw drivers
I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.
My Orders
