795741 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice chute would not open.
18 of 54 people
found this instruction helpful.
-
Steve from MUKWONAGO, WI
- Easy
- 30 - 60 mins
-
Screw drivers
Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.
Was this helpful?
Thank you for voting!
icemaker quit
10 of 31 people
found this instruction helpful.
-
marvin from montgomery, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
i first replaced valve as the water line hung up and broke the valve as i was moving fridge out,be careful about doing this,now i need to replace icemaker as its not working,ps it wasnt the water valve ,i broke it,so first replaced it now icemaker ,lg stinks for the 2 yrs icemaker has worked,my previous kenmore icemaker thru door worked f
... Read more
or 23 yrs and was working the day i replaced it, the new electronic appliances are nice when they work!!!>Marvin
Read less
Was this helpful?
Thank you for voting!
replace hand screw
2 of 11 people
found this instruction helpful.
-
dorothy from SALISBURY, MD
- Very Easy
- Less than 15 mins
-
Screw drivers
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle
... Read more
in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
Read less
Was this helpful?
Thank you for voting!
Frost in the freezer. Icemaker frozen.
1 of 8 people
found this instruction helpful.
-
Teresa from Miami, FL
- Really Easy
- More than 2 hours
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Was this helpful?
Thank you for voting!
Water/ice maker not working
9 of 37 people
found this instruction helpful.
-
Brent from ROGERS, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Was this helpful?
Thank you for voting!
Torn door gasket
-
Robert from Lake Mary, FL
- Really Easy
- Less than 15 mins
Easy replacement job
Was this helpful?
Thank you for voting!
The gasket on our bottom drawer freezer was torn
-
Pat from West Bend, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Too
... Read more
k all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!
Read less
Was this helpful?
Thank you for voting!