7957403 Kenmore Refrigerator - Instructions

Removed upper drawer/basket from freezer

Removed 2 Philips screws

Removed rail bracket assembly

Reinstalled reversing those steps

Works like new.
Happy wife. Happy life. FYI- I am nearly 77 yrs young.

Unscrewed what remained from broken door stop, aligned new one, screwed it in. Done!

Inserted the new shelf

Took 2 screws out and disconnect wire and install new part.

Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.

I started by emptying the food out of the refrigerator. Because of the placement of the refrigerator, it was hard for me to open the doors all the way, but I managed to remove the vegetable drawer, the fruit drawer, the deli drawer drawer, and glass that goes in the tray. Once that happened, I realized my refrigerator was a biology experi ... Read more ment in progress.
Using my steam cleaner, I cleaned everything that I could and the refrigerator actually looked almost brand new.
I removed the deli tray to have more room to get the whole tray and side guides . Once you do that. the tray is actually very easy to replace. The guides were still in pretty good condition although I ordered one more because it did have a small crack and eventually it will break.
You remove the three guides (left, right, and center) from the old tray and attach the new tray fram.
Sounds Easy, right?
It takes a bit of finagling because " the magic tray" which is part of the vegitable drawer has to be placed before you put the right guide on. this process is a bit awkward. if you can get an extra hand, it helps. After that, it was very easy to just put things back and I took this opportunity to clean the rest of my refrigerator and re-organize. I am going have to do this again because I have to replace the right guide, which has a crack, but so far it's working great it is not a problem. Nothing that a little duct tape can't solve until the real thing comes along. This project took longer than I thought it would. But that was primarily because I also cleaned the refrigerator, and put the right guide on before I figured out I had to put the humidifier cover in first. I think that's really the key step here.
I leave you with this: I researched how to find these parts and this site t was great. I can replace all of the hardware that breaks in my refrigerator for less than it costs to buy a new refrigerator. My friend felt I should just dump the refrigerator and start new. As other DIY people, that was like fingernails on a chalkboard for me. It's wasteful to the environment and economically unfeasible. So celebrate your project's end!

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

Removed the old one and replaced with new just remember do your do diligence watch YouTube videos makes repair a lot easier

i changed the filter and was able to get water to the white coil at the bottom of the dispenser (left door) but could never get water to the icemalker.i also replaced the pump at the bottom of the door as well as the green ebr699172 dispenser electrical board.still can not get water to the icemaker.any help will be greatly appreciated.< ... Read more br />paul

i removed old and installed new gasket in 5 minutes. i watched a video. it was super easy .

Phillips head screw driver required.

Door stopper attaches to door and front side of refrigerator. Located at the underside of the door at the front of the hinge.

Remove screw, keep screw for installation of new stopper. Remove damaged stopper, install new stopper using the original screw.

I replaced the whole self-contained unit. I removed the old ice bin simply by lifting it out of the door and replacing it with a new one directly under the ice maker. It was a simple fix; no tools or service tech were required.

Very good removed old gasket and install new one in under 5 mins.

Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice ... Read more buildup.