My Orders
- Home
- 79573157610
- Instructions
79573157610 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water feed line running from water valve to filter housing was leaking
13 of 21 people
found this instruction helpful.
-
Tom from EASTON, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter
... Read more
housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Read less
Was this helpful?
Thank you for voting!
Ice Maker Quit Making Ice
8 of 12 people
found this instruction helpful.
-
Jeff from HUMBLE, TX
- Very Easy
- Less than 15 mins
-
Screw drivers
For this model the ice maker is very easy to replace. All it takes is a phillips head screwdriver. There are two wire connections you have to unplug. Easy out easy in. You do not have to disconnect the water line, just make sure the line is lined up correctly when you reinstall the new icemaker. It seems to take approximately 8 hours befo
... Read more
re you start getting ice again. If you have this same model, you already know this ice maker is very slow in making ice and is not able to keep up with daily usage of ice for a household of 3.
Read less
Was this helpful?
Thank you for voting!
Fridge waterline for ice maker / door water
6 of 8 people
found this instruction helpful.
-
Todd from MARS HILL, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Read less
Was this helpful?
Thank you for voting!
Changing out the Ice Maker tube
9 of 19 people
found this instruction helpful.
-
HARRY from SPARKS, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Read less
Was this helpful?
Thank you for voting!
Filter housing leaking
4 of 4 people
found this instruction helpful.
-
Larry from CLEMMONS, NC
- Really Easy
- 30 - 60 mins
Removed old filter head, installed the new head
Was this helpful?
Thank you for voting!
Ice maker stopped working
4 of 5 people
found this instruction helpful.
-
Orlando from MESA, AZ
- Easy
- 30 - 60 mins
-
Screw drivers
The Ice Maker from Part Select was complete. Plastic housing, Ice maker located at the top and ice cruncher/dispenser at the bottom.
Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.
Note: Both the ice maker and the dispenser wiring goes to a common connecter. It is not advisable to plan changing out only one of these.
Was this helpful?
Thank you for voting!
Replace water filter
4 of 6 people
found this instruction helpful.
-
Bill from FORT SMITH, AR
- Very Easy
- Less than 15 mins
Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.
Was this helpful?
Thank you for voting!
Replaced hose and it was exactly what I needed.
3 of 5 people
found this instruction helpful.
-
Donald from CLEBURNE, TX
- Very Easy
- 30 - 60 mins
-
Screw drivers
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this helpful?
Thank you for voting!
The shelf on our refrigerator was cracked so I ordered a replacement.
3 of 5 people
found this instruction helpful.
-
Scott from KENT, WA
- Very Easy
- Less than 15 mins
Some have said that the installation took 5 minutes. Mine took less than that, and I did it with one hand. I had a beer in my other hand.
Was this helpful?
Thank you for voting!
Broken Door Basket
2 of 3 people
found this instruction helpful.
-
Theodore from SACRAMENTO, CA
- Very Easy
- Less than 15 mins
Un-wrapped the basket......Installed with NO tools......
Was this helpful?
Thank you for voting!
Replaced cracked refrigerator door shelvers
1 person
found this instruction helpful.
-
Larry from SANTA ROSA, CA
- Very Easy
- Less than 15 mins
Slid the replacement shelves into place.
Was this helpful?
Thank you for voting!
The door bin cracked and broke.
1 person
found this instruction helpful.
-
Elizabeth from Huntington Beach, CA
- Very Easy
- Less than 15 mins
I just popped out the broken bin and slid the new one into the slots on the door.
The fix was easy. I appreciate the expert advice on which part to purchase, as that was difficult to figure out. I received a prompt response to my question and the replacement part came quickly.
The fix was easy. I appreciate the expert advice on which part to purchase, as that was difficult to figure out. I received a prompt response to my question and the replacement part came quickly.
Was this helpful?
Thank you for voting!
Large basket inside right door was broken.
1 person
found this instruction helpful.
-
Steve from DENHAM SPGS, LA
- Really Easy
- Less than 15 mins
Removed the old one and replaced with the new.
Was this helpful?
Thank you for voting!
Ice maker compartment icing
2 of 4 people
found this instruction helpful.
-
Jerry from RIDGEFIELD, NJ
- Very Easy
- Less than 15 mins
-
Screw drivers
Remove 3 screws bottom and base.
Loosen top screw. Pull out from bottome and unplug wire harness.
Loosen top screw. Pull out from bottome and unplug wire harness.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken door basket
2 of 4 people
found this instruction helpful.
-
William from LARGO, FL
- Very Easy
- Less than 15 mins
The repair was an easy replacement. The problem was the LG part was no longer available from LG or any of the other places I tried. The PartSelect customer service representative was a true professional and did an outstanding job of helping find the correct part (LG's diagram was unreadable) and cross-referenced it to find the the part th
... Read more
at PartSelect actually had in stock. I had the part in four day. The best customer service I have had in years. I lost his name but the order was 13449146. He deserves a raise!
Read less
Was this helpful?
Thank you for voting!