All Installation Instructions for Kenmore Refrigerator 795730

Spring broken in door mullion

1 person found this instruction helpful.

Wayde from SEMINOLE, FL
Really Easy
Less than 15 mins
Screw drivers

Took 2 screws out and disconnect wire and install new part.

Was this helpful?

The spring on the mullion was broken so the mullion would not open to seal the other door.

1 person found this instruction helpful.

JANET from GRAND JCT, CO
Very Easy
Less than 15 mins
Screw drivers

I am a73 year old woman. If I can do this, anyone can. Super easy. Just watch the online video.

Was this helpful?

Removed old part.

1 person found this instruction helpful.

Steve from NORTH AURORA, IL
Very Easy
Less than 15 mins
Screw drivers

Installed new one.

Was this helpful?

Old part did not seal properly

1 person found this instruction helpful.

Donald from MERRITT IS, FL
Really Easy
Less than 15 mins
Screw drivers

Read the reviews from other members and just did as they said. Needed a screw driver and the info from past persons review couldn’t have been easier.

Was this helpful?

Previous glass shelf shattered into a million pieces while cleaning.

1 person found this instruction helpful.

Susan from SAFETY HARBOR, FL
Really Easy
Less than 15 mins

Just laid the shelf down. Fit like a glove!

Was this helpful?

Ice Maker and Water dispenser stopped working

2 of 4 people found this instruction helpful.

Donald from BETHPAGE, NY
Really Easy
15 - 30 mins
Pliers, Screw drivers

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Was this helpful?

Broken spring on flapper door

1 person found this instruction helpful.

Richard from IMPERIAL, CA
Very Easy
15 - 30 mins
Screw drivers

Unplugged the frig and removed two phillip screws on flapper door of left door... Unplugged the electrical connector and removed flapper...
Picked up new flapper and snapped electrical contractor together... Slid new flapper bar into place and inserted two phillip screws... Job complete in 15 minutes...

Was this helpful?

Lights didn't come on when door was opened

1 person found this instruction helpful.

Philip from Ashland, MA
A Bit Difficult
15 - 30 mins
Pliers, Screw drivers

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Was this helpful?

Spring in the plate front assembly broke. Door plate assembly would not move into correct position, preventing door from closing.

1 person found this instruction helpful.

Robert from WARREN, RI
Very Easy
Less than 15 mins
Screw drivers

Followed Youtube video provided on the PartsSelect Website:

https://www.partselect.com/PS12374439-LG-AGU75188619-PLATE-ASSEMBLY-FRONT.htm?Inventory=12374439&SourceCode=20&SearchTerm=LFX28979ST

Made installation of the new part a piece of cake. Easy peasy!! Took less than 10 minutes.

Was this helpful?

roller was missing in freezer upper drawer

1 person found this instruction helpful.

Bob from LIBERTY TWP, OH
Really Easy
Less than 15 mins

easy, just lift the drawer and insert the roller assy.

Was this helpful?

door slight switch failed

1 person found this instruction helpful.

Greg from CASA GRANDE, AZ
Really Easy
Less than 15 mins
Pliers

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.

Was this helpful?

Door light switch, 3rd one I have replaced in 6 years made in China.

1 person found this instruction helpful.

Charles from CURWENSVILLE, PA
Really Easy
Less than 15 mins
Pliers, Screw drivers

Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE

Was this helpful?

Replace switch

1 person found this instruction helpful.

Dean from HILLSDALE, MI
Really Easy
Less than 15 mins
Screw drivers

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Was this helpful?

The switch became intermittent - Possibly a poor designe

1 person found this instruction helpful.

Sidney from ENDICOTT, NY
Very Easy
Less than 15 mins
Screw drivers

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Was this helpful?

The glass shattered & needed to be replaced

2 of 4 people found this instruction helpful.

David from HAMPTON, GA
Very Easy
Less than 15 mins

Just popped it in, just as easy as that!

Was this helpful?

795730 Kenmore Refrigerator - Instructions