My Orders
- Home
- 79572372310
- Instructions
79572372310 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water feed line running from water valve to filter housing was leaking
13 of 21 people
found this instruction helpful.
-
Tom from EASTON, PA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Shut off water supply. Disconnect main supply line. Remove rear lower panel on back of refrigerator. Remove all tubing clamps on back. Disconnect leaking tubing from water supply valve. Remove water filter and unscrew/remove water filter housing. Replace tubing - connect to water filter housing then to water supply valve. Reconnect filter
... Read more
housing and filter. Reinstall lower panel, then main water supply line, then all tubing clamps. Turn water back on and check for leaks after discarding several glasses of water to fill filter. Job complete!
Read less
Was this helpful?
Thank you for voting!
Fridge waterline for ice maker / door water
6 of 8 people
found this instruction helpful.
-
Todd from MARS HILL, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
The heavy work is moving the fridge, then take off the lower plans. Use a bowel or cup for screws and the water line connector spacers so you don't loos them.
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
undo connections holding water line, including the bottom brakes for the solenoid. Reuse the spring around the lower waterline to prevent external wear on the line.
... Read more r />NOTE: remove the waterline connector spacers and save!
NOTE: you must compress (not pull) the connect to then pull the waterline out of the connectors.
NOTE: You must also remove the water filter and housing inside the fridge but this is easy.
MOTE: Test the line for leaks by turning on the water and then using the door water. The filter will need to refill so it may take a minute before water comes up. This line only have pressure when the door water is used or the ice maker needs to make ice.
After replacing the line, test the line for leaks by using the door water so the solenoid fills the lines
Read less
Was this helpful?
Thank you for voting!
Changing out the Ice Maker tube
9 of 19 people
found this instruction helpful.
-
HARRY from SPARKS, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
An easy way to get a refrigerator out from the wall is to use a tow strap or 1/2 to 3/4 in. rope. Throw a loop behind refer while keeping both ends in your hands. Let it settle down to the lower half of unit and pull using both hands. Comes right out.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Remove lower panel. Unscrew water valve from cabinet. Remove all tube holders L ... Read more ay some rags down to catch a little water drainage.
Turn off water supply valve at wall. Unplug Power. Remove filter and filter holder. (one screw).
remove tube from valve by removing plastic C clip. Push plastic ring towards the valve and pull out tube at same time.
With the tube free, remove filter, then mount screw to remove the inside filter holder. When it is out, pull the tube doing the same process as the lower end. Pull tube out and replace with new one putting everything back in reverse order.
Before placing tube holders back on, turn on water to check for leaks.
After turning water back on and plugging in power, push refer back into place.
While I was there, I also replaced the hose from the wall to the refer.
Read less
Was this helpful?
Thank you for voting!
Door stopper broke
5 of 9 people
found this instruction helpful.
-
ROGER from SCHELLSBURG, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Installed new door stopper with screw driver on bottom of french door
Was this helpful?
Thank you for voting!
Ice maker wore out.
3 of 3 people
found this instruction helpful.
-
Thomas from LA PLACE, LA
- Really Easy
- 30 - 60 mins
-
Screw drivers
I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker
Read less
Was this helpful?
Thank you for voting!
Left side gasket was torn and would seal properly
3 of 4 people
found this instruction helpful.
-
Thomas from CHULA VISTA, CA
- Easy
- Less than 15 mins
-
Screw drivers
Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.
Was this helpful?
Thank you for voting!
Icing up in the freezer due to poor gasket
2 of 2 people
found this instruction helpful.
-
Maryann from BROOKFIELD, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Watched a couple of YouTube videos and then went at it
Was this helpful?
Thank you for voting!
Replaced hose and it was exactly what I needed.
3 of 5 people
found this instruction helpful.
-
Donald from CLEBURNE, TX
- Very Easy
- 30 - 60 mins
-
Screw drivers
Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock
Was this helpful?
Thank you for voting!
Ice crystals appearing on the face of the freezer draws
2 of 2 people
found this instruction helpful.
-
Craig from SPRING HILL, FL
- Really Easy
- Less than 15 mins
Part Select had a great video which made the repair easy, using a putty knife to start removing the freeze door gasket. Once removed the install is simple just snap the new gasket into the track, but start at the corner. Other company's have a video requiring you to remove the entire freezer compartment out of the appliance, unnecessary w
... Read more
aste of time and labor.
Read less
Was this helpful?
Thank you for voting!
The Ice maker stopped working
2 of 4 people
found this instruction helpful.
-
Joseph from SAINT LOUIS, MO
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Thanks to videos on You-Tube which showed step by step removal and replacement. It was a simple process. only thing missing on the video was information on the green ground wire.
Was this helpful?
Thank you for voting!
Freezer door gasket needed replacing.
1 person
found this instruction helpful.
-
Stephen from DICKINSON, TX
- Really Easy
- Less than 15 mins
-
Pliers
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Was this helpful?
Thank you for voting!
Freezer door gasket formed gaps between door and refrigerator.
1 person
found this instruction helpful.
-
Cheryl from Ormond Beach, FL
- Really Easy
- 15 - 30 mins
Removed old gasket from the door and replaced with new gasket.
Was this helpful?
Thank you for voting!
Ice buildup in corner of freezer.
1 of 2 people
found this instruction helpful.
-
Louis from BOYNTON BEACH, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice
... Read more
buildup.
Read less
Was this helpful?
Thank you for voting!
In Door Ice Bin with built-in ice dispenser drive wheel gear broke when dispensing the ice.
1 of 2 people
found this instruction helpful.
-
Steven J from Phoenix, AZ
- Very Easy
- Less than 15 mins
I replaced the whole self-contained unit. I removed the old ice bin simply by lifting it out of the door and replacing it with a new one directly under the ice maker. It was a simple fix; no tools or service tech were required.
Was this helpful?
Thank you for voting!
Side by side refrigerator. Right hand door (door stopper broken)
1 of 2 people
found this instruction helpful.
-
George from ROSEVILLE, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
Phillips head screw driver required.
Door stopper attaches to door and front side of refrigerator. Located at the underside of the door at the front of the hinge.
Remove screw, keep screw for installation of new stopper. Remove damaged stopper, install new stopper using the original screw.
Door stopper attaches to door and front side of refrigerator. Located at the underside of the door at the front of the hinge.
Remove screw, keep screw for installation of new stopper. Remove damaged stopper, install new stopper using the original screw.
Was this helpful?
Thank you for voting!