79572092311 Kenmore Refrigerator - Parts

Add useful storage space inside a refrigerator door with this clear plastic door bin. It holds bottles, jars, drinks, and condiments where they are easy to see and reach. The bin measures about 13-1/2 inches wide and 4-1/4 inches high. Its shaped base is about 9-1/2 inches deep on one side and 10-1/8 inches deep on the other. Installation...Read more requires no tools. Place the bin slightly above the mounting points, then slide it down until it locks into place. Compare the size, shape, and side mounts with the original bin before ordering.

Refrigerator Air Filters are a key component for neutralizing odors and ensuring a fresh stream of air into your refrigerator. Swapping your old filter out for a fresh one isn’t difficult and should take less than five minutes. This OEM filter measures approximately 3 inches (length) x 3 inches (height) x 5 inches (Depth). Air filters should be changed every 6 months depending on usage.

Frost near the door or a freezer that runs often may have a damaged door seal. The flexible gasket blocks room air and moisture from entering the cold compartment. First clean the seal and contact surface, then check the hinges and door fit. Match the replacement to the complete freezer model and door position. If shipping leaves folds, s...Read moreoak the gasket in warm water for 5 to 10 minutes or use a hair dryer on low. Do not overheat the rubber. Smooth each side, close the door, and test the seal with a strip of paper.

This is a micro switch for various models of LG refrigerators. This switch is responsible for turning the ice dispenser on and off within the freezer compartment of the fridge. If this switch is damaged or shorted, it will cause the ice maker to work inconsistently, or not at all. This switch is different from the water dispenser switch, ...Read morewhich has an entirely different shape all together. Replacing this switch is simple and only requires a Philips-head screwdriver to disconnect the old switch and install the new one. This switch is a genuine OEM LG part and does not come with any other parts or accessories.

This fridge gasket, also known as a door seal, is an authentic OEM part supplied by LG for use with various models of LG refrigerators. It is a flexible strip of rubber that sits along the perimeter of the refrigerator. It creates an airtight seal between the door and fridge body to prevent cold air from escaping and warm air from enterin...Read moreg. This helps to keep your fridge cool and energy efficient. If the gasket is worn out, torn, or can no longer maintain a tight seal, your fridge will have to work harder to maintain the correct temperature inside the fridge. You may also notice that the door may not be able to close properly.

The water reservoir holds the water for the water dispenser as the water chills.

This water tubing clip holds the water fill tube in place in your refrigerator. The water fill tube attaches and supplies water to the ice maker/water dispenser in your fridge-freezer. If the tubing is in working order, but is hanging loose inside the unit, the issue could be that the clip meant to hold it in place is broken. If this is t...Read morehe case, you should look to replace the clip. This clip is made of black plastic, and is just over half an inch long. This is a genuine OEM replacement part, and is sold separately.

This refrigerator water filter and filter assembly is designed to improve the quality of drinking water and ice by reducing contaminants such as chlorine, lead, and sediment. Certified to NSF standards 42 and 53, it enhances taste and clarity while allowing beneficial minerals to pass through. Compatible with select bottom-freezer refrige...Read morerator models, this genuine replacement part should be installed using a simple twist-in method and replaced every six months or when water flow slows. After installation, flushing approximately four gallons of water ensures optimal performance and removes any residual carbon particles. Regular replacement supports consistent filtration and helps maintain the appliance’s performance.

This ice bucket assembly is designed to store and dispense ice within select refrigerator models. It includes both the ice bin and the auger mechanism, which rotates to push ice through the dispenser when activated. The assembly is intended to replace a damaged or malfunctioning unit, restoring full ice dispensing functionality. Measuring...Read more approximately [insert dimensions if known], it is constructed from durable, food-safe plastic and features a clear finish for easy visibility of ice levels. Installation is straightforward and typically requires no tools—simply remove the old assembly and slide the new one into place, ensuring it aligns securely with the dispenser mechanism. Before purchasing, verify compatibility with your refrigerator model to ensure a proper fit.