7957206 Kenmore Refrigerator - Instructions

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

I have moderate to good mechanical skills, but getting the old switch out was a sizeable challenge. Since this switch suffered some damage during extraction, I was lucky to have ordered a new one to replace it. Reinstall took approximately 90 seconds. PartSelect saved me an expensive service call.

Called a local repair shop to get the problem diagnosed. Nice repair guy came out and was pretty confident that it was the main board . However his supplier had it on backorder and had a 7 day shipment estimate. When he told me I got on the internet and parts select had the part in stock with a 2-3 business day arrival. I rolled the dice ... Read more and ordered it. Came the next day via Fed x. It took me 15 minutes to put it in and so far so good. Without the diagnosis I would have been in the dark as to what was wrong so it was worth the fee for the service call to get an expert diagnosis

Removed old gasket from the door and replaced with new gasket.

1. Unplug the refrigerator (to avoid shock) 2. With one screwdriver pry open the switch on the side facing the door to a gap of about 1/8 inch 3. Insert a second screwdriver into the gap to press the plastic tab back slightly and this should release the part. 4. pull the part out and unplug it, you may have to pry back some small tabs o ... Read more n the sides, 5. Plug in the new switch 6. plug in the refrigerator the light should come on, if not tighten the connection 7. Insert new switch back into its slot, it should snap in place. Done!

The 2 minute or so video was not exactly matching the model that we had but the instructions were very good and important. The switch was a little difficult to get out from the side of the refrigerator.

Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.

I ordered the needed parts, the correct ones I thought, but when they arrived, I realized they were the wrong parts shipped to me. The reason the wrong parts were shipped to me was because PartsSelect failed to advise me there were none of the parts I needed available so they shipped the left hand basket assembly, door, versus the desire ... Read more d right hand basket assembly, door. I then had to return the wrong parts shipped to me, at my cost of ~$25, and await a refund for the wrong parts originally shipped to me. That's how I did the repair.

The repair was an easy replacement. The problem was the LG part was no longer available from LG or any of the other places I tried. The PartSelect customer service representative was a true professional and did an outstanding job of helping find the correct part (LG's diagram was unreadable) and cross-referenced it to find the the part th ... Read more at PartSelect actually had in stock. I had the part in four day. The best customer service I have had in years. I lost his name but the order was 13449146. He deserves a raise!

Removed upper drawer/basket from freezer

Removed 2 Philips screws

Removed rail bracket assembly

Reinstalled reversing those steps

Works like new.
Happy wife. Happy life. FYI- I am nearly 77 yrs young.

I just popped out the broken bin and slid the new one into the slots on the door.

The fix was easy. I appreciate the expert advice on which part to purchase, as that was difficult to figure out. I received a prompt response to my question and the replacement part came quickly.

Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape

Slid the replacement shelves into place.

Covered the sidewall with tape to protect. Pried the switch out with knife blade and removed electric plug with needle nose pliers. placed plug in new switch and pushed switch into the hole in the side wall. Took about five minutes.