7957205 Kenmore - Instructions

Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!

Unplugged the refrigerator. Used small flat head screw driver to push the front tab of the old switch in and pulled it out with pliers. Detached and reattached the wires to the switch. Reinserted back into hole. Plugged refrigerator back in to power. All good.

I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very ... Read more strong !!

Followed directions that came with the filter. Did remove the top shelf for easier access. Very simple and quick.

Removed 4 screws then removed ice maker unit. Unplugged the old unit. Checked and verified the inlet tube was clean and not blocked. Plugged in the new unit. Placed unit into proper location and verified it was properly in place. Replaced the 4screws. Turned on the unit closed the ice door and it started making ice maybe an hour later by ... Read more morning the ice bucket was full. Super easy.

pried out old switch, disconnected wires ,placed wires on new switch

Watch YouTube videos on this topic if you are uncertain before tackling the job. The right door was easy to replace. Just pull the gasket with your fingers and it will come off easily. Place new gasket over door and use fingers to press it inside the groove few inches at a time. Pay attention to gasket orientation.

The left ... Read more door is a bit harder because you need to remove the mullion at the door edge using a screw driver. Remove two screws on the center hinge and then slide the mullion up to disengage. Then unplug the wires to remove the mullion. Replace the gasket as described above and replace the mullion reversing the directions shown above.

Could not believe how easy it was!

I actually watched a YouTube video for LG refrigerators. The hardest part was taking the wire harness out. Mine was really stuck in there. But got it, put the new switch in and viola it worked. Yay!

Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.

I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker

Fortunately, others had left comments about this installation, so proved very helpful. First thing was laying out the gasket flag on the counter to allow it to unbend, get out the kinks from shipping. While the new gasket was laying out on the counter, started removing the old gasket. As it had been there for 11 years, needed pliers to ... Read more get a corner started. I was slow and careful removing the old gasket in case I needed to put it back in. A very helpful suggestion from others was to lightly rub dishwashing soap on the gasket edge that fits in the groove in the door. Again, slow and careful, got it installed, wiped off any excess dishwashing liquid, and the door closed with a better seal in a long time. Pleasantly surprised how easy this was to do!

Replaced Ice maker unit

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new sw ... Read more itch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

Took off the French door Mullen by unscrewing middle area. Unconnected the wires for the door sensor. Then detached old gasket and replaced with new gasket. Reattached the wiring and snapped Mullen flap in place and finally rescrewed to the door. Seal is very good now.

Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.