79571072014 Kenmore Refrigerator - Instructions

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new ... Read more water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first ... Read more by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

Took 2 screws out , pushed flapper up, unhooked wire connector, reversed to install new door. Less than 5 minutes. So easy , a caveman could do it.

When I sent an email about this and asked for a replacement, I was told I would need to send it back. I wrote back and reiterated that the glass was shattered and did they really want me to send it back. I again said just send me the replacement. Instead I got a response that sending it back was not necessary but that I would receive a re ... Read more fund and would need to reorder the part again. The part was $47.91 when I first purchased it. Now to reorder it is $54.98. I saved it in my shopping cart so I can shop around before purchasing this again. I am disgusted that I need to go through this again and now at a higher price. I have more parts to order but am reconsidering do so.

I ordered the part from Partselect, received it two days later, installation couldn’t be easier, remove two screws from the hinge and slide the old part out, remember to unhook the electric line. To install just do it in the opposite order.

I installed the new 3 wire ice maker very easily, but it was defective. I was told that instructions for the return of the defective part would be sent later due to the virus. I have never received the return instruction.
I did receive a credit for the defective part. VERY Satisfied with y’all’s service.
Waiting for return i ... Read more nstructions if y’all still want it back.
Thanks,
Thomas Pennebaker

I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very ... Read more strong !!

Removed old bucket and placed new one In its place. New one is actually better than OEM part because it has an arm than breaks up any ice that may jam.

Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with va ... Read more lve assembly in reverse order

Expensive to have repair man come out and find out that I’ve been mailed wrong spring again. My icemaker is on the left hand side this is the side of refrigerator- I need the spring for left side with the ice maker. Twice they have mailed me the Wrong spring that goes on the right hand side I have tried to explain this to the person that ... Read more waits on me. Do I have to pay for another spring and mail this one back ?i have mailed one back and postage is getting expensive.

Removed mullion strip with Phillips screwdriver replaced spring reinstalled the mullion strip all in about 15 minutes.

Removed the 2 Phillips head screws that attach the flipper assembly to the door. Slide the flipper assembly up to disconnect the top & bottom bracket. Disconnect the quick connect wire assembly behind the center hinge bracket and remove the flipper assembly. Install the new flipper assembly in reverse order.

Removed two screws from door and three locking brackets with a small common screw driver. Raised the bracket, slide in the spring, held down the bracket, installed screws and plastic covers. Less than 2 minutes. Easy application no problem with the new spring or ,mullion..

Swapped old one with new one. New one had extra plug not needed.