- Home
- 79096613402
- Instructions
79096613402 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
inner glass uncleanable
-
Krista from Newtown, CT
- Easy
- 15 - 30 mins
-
Screw drivers
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Was this helpful?
Thank you for voting!
Broiler element broken
-
Robert from Newark, DE
- Easy
- 15 - 30 mins
-
Screw drivers
Removed broken element, four screws. Element ends were attached to the oven via wire clips. Removed those too. Placed clips on the ends of the new element and remounted to the top of the oven enclosure with the fours screens. Took twenty to twenty five minutes. We had Tbones a little while later. Saved over 125.00 for repairman.
Was this helpful?
Thank you for voting!
broiler element burned out.
-
Kellyjean from Springfield, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this helpful?
Thank you for voting!
oven would turn on and stay on regardless of set point
-
robert from Mansfield, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Pulled oven from counter space unplugged unit unscrewed 9 - 1/4" tech screws then one more 1/4" tech screw that holds the sensor.Inserted the new element cut the two wire because it was a different connection stripped the wires and did the same to the old element but used the old plug.Connected the plug,plugged the over back in slid the u
... Read more
nit back and turned out on for a test.All is well,thank you!
Read less
Was this helpful?
Thank you for voting!
oven was too hot code f-10 came up
-
Donnie from McLaughlin, SD
- Really Easy
- 15 - 30 mins
-
Nutdriver
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this helpful?
Thank you for voting!
The warning light for the warmer was stuck "on"
-
Linda from Pleasant Mount, PA
- A Bit Difficult
- 15 - 30 mins
Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and th
... Read more
e electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.
Read less
Was this helpful?
Thank you for voting!
really bad ugly streaks inside of glass
-
John from Hemet, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door
... Read more
. Just reverse the way you take it apart to put it back together.
Read less
Was this helpful?
Thank you for voting!
Needed to install an anti-tip bracket on my stove.
-
Daniel from Provo, UT
- Really Easy
- Less than 15 mins
-
Socket set
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this helpful?
Thank you for voting!
Aluminum foil on bottem of oven melted and made a mess on new stove
-
Natalie from Beaverton, OR
- Really Easy
- Less than 15 mins
-
Screw drivers
Unscrewed the oven bottom plate and removed. Put new one in place and screwed it in place. Stove looks brand new again and am so happy with the results.The part we received was a perfect match and arrived in a few days!
Was this helpful?
Thank you for voting!
put aluminum foil on bottom panel of oven to catch drips. Big mistake. adhered to oven in minutes.
-
jill from new boston, NH
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 screws at rear of bottom panel. Removed old panel, replaced with new and screwed back in.Piece of cake. Plus this company was great to order from. received part the same day. Very happy. Would order through this company again.
Was this helpful?
Thank you for voting!
damaged bottom pan
-
Neal from Severna Park, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 back screws, lifted pan from rear and pushed front slightly forward/into oven until front lip cleared. Installed new pan in reverse order.
Was this helpful?
Thank you for voting!
lost a rack?
-
Melanie from Reading, PA
- Really Easy
- Less than 15 mins
After removing an oven rack to make room for the thanksgiving turkey roaster, I have NO IDEA, where I might have stowed it away! After searching every cabinet and every closet I realized I needed to do something quick for our annual christmas cookie marathon that would begin on Sunday. It was so easy to order the part, it arrived the next
... Read more
day, and we baked for 5 hours using the 3 racks in the convection oven. Dozens of cookies later... Thank you Parts Select!
Read less
Was this helpful?
Thank you for voting!
Purchased home where previous owner melted Aluminum Foil to bottom panel of oven.
-
Michael from Wimauma, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 screws from rear of panel and dropped new panel in. Re-installed screws. Oven like new again. Aluminum foil was burning and emitting foul odor when oven was on.
Was this helpful?
Thank you for voting!
Broken oven door glass
-
Joseph from Cranberry township, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed directions for replacement of the glass from the web. Replacement was simple and easy.
Was this helpful?
Thank you for voting!
Door glass cracked
-
Mike from Collegeville, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.
Was this helpful?
Thank you for voting!