79096604500 Kenmore Range - Instructions

TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range bac ... Read more k in place. DONE

All of a sudden, one element in our glasstop range would not light and heat up. My wife and I were not sure what to do. Looked it up on the internet, found that you can do it yourself as others desribed the process of accessing the elements below. We decided to do that. It takes two people as one is holding up the glass because it ope ... Read more ns like a car hood. While we diagnosed it was not a wiring issue (found a burnt wire, rewired the burnt wires (after mending the non burnt portions) to another element. The element that was not working before still did not turn on. Decided to purchase an element. While many online places sell elements, PartSelect actually allowed searching by brand with exploded views of the range to select the exact parts. This lessened the worry of purchasing a wrong element. When the part came (almost one day later), the repair was less than five minutes. Thank you PartSelect. I feel I saved a lot of money and aggravation.

I went all the way around the unit and removed screws holding top of unit in place. Removed knobs holding front panel in place. Remove control panel. top should come off. Remove screws attaching element top and metal frame. Undo bracket and remove element. Disconnect wires. Remember where they were attached.
Replace element and rever ... Read more se steps.

Disconnected power. Removed hold down fasteners for stove top. Fortunately, I did not flue down or use the double back tape to secure stovetop to counter. If this adhesive were used, it is possible I would have had great difficulty in removing range. I did not disconnect the wiring, but turned the range top over to access the cover. ... Read more I removed the cover and easily removed the failed burner and installed the new ones. I had to pull 4 wires from the terminal strip and reattach them. The hold down strap for the burner was reinstalled. Range top turned back over and fastened down. Back in service.

Disconnected power at breaker. Removed cooktop mounting screws, lifted top and propped in up position. Removed two screws and lowered two front burners mounting frame. Wiggled dual element free at the clips and proceeded to swap wires one at a time and realized the difference with connectors 1a and 2b much later when only the center porti ... Read more on was heating up. Finally figured out the problem and everything works as advertised. Pay attention if you own a Kenmore product.

Followed the instruction printed on the page, while ordering the part.

Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included ... Read more putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

Self easy

PS Great service Super FAST.
Thanks Jesse

First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connec ... Read more t them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Removed back off of stove. Removed two screws that held in the switch, removed the wires that were connected to the switch and replaced the part.

Followed on-line instructions to remove the defective heating element. Some connection tabs on the replacement unit were different than the original. One tab was too wide to accept the stove's slip-on wire connector without fling down the tab width on the heating element. Thanks to some on-line instructions, wire connections to element 1a ... Read more and 2a had to be reversed. If not for those instructions I would probably have ended up sending the unit back to the supplier, as an incorrect replacement !

My husband followed the video instructions and it was easy to fix.

Twisted replacement bulb into place easily. Let there be light!

Went very well and it works!

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.