- Home
- 79096523402
- Instructions
79096523402 Kenmore Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
There was no instructions. The wires don't match up old vs new. I read the reviews and this helped.
2 of 3 people
found this instruction helpful.
-
Lisa from APACHE JCT, AZ
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
However the 1a 1b etc. Are very hard to see thus the need to magnify. Then it was easy.
I must say the guy I talked to was very nice.
I must say the guy I talked to was very nice.
Was this helpful?
Thank you for voting!
. F3 error code
1 person
found this instruction helpful.
-
Garry from New Haven, CT
- Really Easy
- 30 - 60 mins
-
Nutdriver
I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install
Was this helpful?
Thank you for voting!
Element would not heat up
1 person
found this instruction helpful.
-
Everett from Colchester, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed 2 screws located underneath the front lip of the range top. Lifted range top and supported. Removed the 2 screws at either end of the support bracket. This bracket holds the elements in position. Be careful not to let the elements fall out when removing. The elements are now free to replace. Swap out the old with the new and be su
... Read more
re to reconnect the wires to the correct terminals on the new element. I did 1 wire at a time so as to not make a mistake at reconnecting the wires. Then replace the support bracket with the 2 screws and lower the range top in place and put back the 2 screws that hold the range top in position. VOILA!! Success. It works. The wife is now happy again:)
Read less
Was this helpful?
Thank you for voting!
wrong part received and returned
1 person
found this instruction helpful.
-
Rhonda from PACHECO, CA
- Very Difficult
- More than 2 hours
I wanted the bracket for the oven heating element and received the bracket for the broiler.... part returned and now I am stumped about what my next move will be
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people
found this instruction helpful.
-
Denise from Landover, MD
- Really Easy
- Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Lens cover for oven light broke.
0 of 1 people
found this instruction helpful.
-
Amy from Corona, CA
- Really Easy
- Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!
temp was not reading right
3 of 10 people
found this instruction helpful.
-
santa from glassboro, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
remove back panel took out old part splice wire replaced
Was this helpful?
Thank you for voting!
The screw head was stripped and couldn't be extracted with a Phillips head screwdriver
1 of 5 people
found this instruction helpful.
-
Robert from GLEN BURNIE, MD
- Very Easy
- Less than 15 mins
-
Screw drivers
If you do not intend to take apart the oven door to clean the interior glass, I would recommend you use a clamp to hold the handle and oven door tightly together while you replace the screw. There is a spacer between the back and front panels which could otherwise be shifted out of position. I used a screw extractor to remove the damage
... Read more
d screw and then installed the replacement. Wish all appliance repairs were this easy!
Read less
Was this helpful?
Thank you for voting!
Cracked inside glass
0 of 2 people
found this instruction helpful.
-
patti from Greer, SC
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
I actually watched Youtube while I was changing it. This video was not actually the same make up of my oven, even though the I typed in the model number. I manage to figure it any with the steps anyway. It was harder then I expected but not horrible. I think I did pretty well for a women. Patti
Was this helpful?
Thank you for voting!
Burner quit working
0 of 4 people
found this instruction helpful.
-
Abe from Manson, WA
- Really Easy
- Less than 15 mins
Received the new part FAST. Ordered online. Easy to plug in the new part. Will use PartSelect.com again when needed to order parts!
Was this helpful?
Thank you for voting!
Broken globe in oven and burnt out light bulb
0 of 5 people
found this instruction helpful.
-
Sharon from Foley, AL
- Really Easy
- Less than 15 mins
Easy as 1-2-3
Other Parts Used:
Was this helpful?
Thank you for voting!
Temperature not correct.
-
David C from Huntington Beach, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to sp
... Read more
lice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.
Read less
Was this helpful?
Thank you for voting!
Sensor probe was not sebding proper temp to themostat which regulate the 2 heating elements.
-
Grayson Crisis enter from Sherman, TX
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and
... Read more
you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.
Read less
Was this helpful?
Thank you for voting!
oven was too hot code f-10 came up
-
Donnie from McLaughlin, SD
- Really Easy
- 15 - 30 mins
-
Nutdriver
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this helpful?
Thank you for voting!
broiler element burned out.
-
Kellyjean from Springfield, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed the old element (2) screws, then unscrewed the (2) brackets holding the element up, pulled the element out of the back wall of the oven unhooked the (2) electrical wires and left them hanging. Installation is in the exact reverse order.
Was this helpful?
Thank you for voting!